92 TOY's 22re / crapped out / gotta start somewhere / thread
May 19, 2010 | 07:59 AM
#2601
Thread Starter
YotaTech Milestone-Two Millionth Post
Joined: Jan 2009
Posts: 12,009
Likes: 122
From: Northeast Pennsylvania
May 19, 2010 | 08:07 AM
#2604
Contributing Member
Joined: Feb 2008
Posts: 12,248
Likes: 33
From: Lake City, Fl
actually...
I'm pretty sure you had it right to begin with
that's how mine were too, both before and afer the 1" diff drop
I'm not sure how much of a difference it would make though...
Last edited by iamsuperbleeder; May 19, 2010 at 08:09 AM.
May 19, 2010 | 08:24 AM
#2607
Contributing Member
Joined: Feb 2008
Posts: 12,248
Likes: 33
From: Lake City, Fl
LOL, sorry 
but, either the threads on those bolts are shot and are not allowing you to tighten them down all the way, or those bushings are shot and squished, becuase there definately shouldnt be a gap like that between that lower washer/plate and the bushing
but, either the threads on those bolts are shot and are not allowing you to tighten them down all the way, or those bushings are shot and squished, becuase there definately shouldnt be a gap like that between that lower washer/plate and the bushing
Last edited by iamsuperbleeder; May 19, 2010 at 08:26 AM.
May 19, 2010 | 08:37 AM
#2610
That is really strange, 92. Must be a shredded thread, right? What I mean is, like bleeder said, " maybe it's not allowing you to snug it up all the way?" ...the NUT I mean.
I guess you're Profile ID pic is right on time at the moment, eh? "O-CRAP", ...I must have said that 400 times in the last few weeks, haha. Pulling for you, 92, just BREATHEEEEEEEE!
I guess you're Profile ID pic is right on time at the moment, eh? "O-CRAP", ...I must have said that 400 times in the last few weeks, haha. Pulling for you, 92, just BREATHEEEEEEEE!
May 19, 2010 | 12:18 PM
#2612
Thread Starter
YotaTech Milestone-Two Millionth Post
Joined: Jan 2009
Posts: 12,009
Likes: 122
From: Northeast Pennsylvania
and with these next pics, i say GOOD DAY to you sir Reed Valve!!!
Pointing at the hose i took off to get more wiggle room. cannot, i repeat, cannot get the Reed valve back on it's 2 bolts.......i think i will be OK, it weighs less than a pound and will be supported front and back by other stuff, so i think i will be alright.
Pointing at the hose i took off to get more wiggle room. cannot, i repeat, cannot get the Reed valve back on it's 2 bolts.......i think i will be OK, it weighs less than a pound and will be supported front and back by other stuff, so i think i will be alright.
May 19, 2010 | 12:22 PM
#2614
Thread Starter
YotaTech Milestone-Two Millionth Post
Joined: Jan 2009
Posts: 12,009
Likes: 122
From: Northeast Pennsylvania
and i think i broke my back.
i don't think i have to go under the truck again for a while, so i think it will be OK......burns like an S.O.B. at my right hip down my butt.....motrin time.
i don't think i have to go under the truck again for a while, so i think it will be OK......burns like an S.O.B. at my right hip down my butt.....motrin time.
May 19, 2010 | 12:40 PM
#2616
Contributing Member
Joined: Feb 2008
Posts: 12,248
Likes: 33
From: Lake City, Fl
May 19, 2010 | 12:56 PM
#2619
Thread Starter
YotaTech Milestone-Two Millionth Post
Joined: Jan 2009
Posts: 12,009
Likes: 122
From: Northeast Pennsylvania
I'm not gonna say to get your skinny as_ up here and help me. Nope, not gonna say it.
as far as the quitter part.......well what the hell else should i do. i've pryed every which way....i am missing my millimeters as you can see by the pic of the tube bolted in......the plus / minus of leaving it unbolted is that, yes, it should be and is meant to be bolted in but i cannot accomplish that no matter how hard i pry against the brake lines , a/c lines or fuel filter.....get my drift? it is held in place from the front and the back and is no more moveable than anything else bolted down.
as far as the quitter part.......well what the hell else should i do. i've pryed every which way....i am missing my millimeters as you can see by the pic of the tube bolted in......the plus / minus of leaving it unbolted is that, yes, it should be and is meant to be bolted in but i cannot accomplish that no matter how hard i pry against the brake lines , a/c lines or fuel filter.....get my drift? it is held in place from the front and the back and is no more moveable than anything else bolted down.
