YotaTech Forums
0 2026/01/13 02:12:16
0 2026/01/17 02:58:46
0 2026/01/17 02:58:49
0 2026/01/17 02:59:33
0 2026/01/17 02:59:35
This is one of the main support beams for the extra roof along with a support post. They’re both 6 x 8 Doug Firs. Had to take a hedge trimmer to the side just to clear out enough creeper to work.
This is one of the main support beams for the extra roof along with a support post. They’re both 6 x 8 Doug Firs. Had to take a hedge trimmer to the side just to clear out enough creeper to work.
0 2026/01/23 18:14:25
Support beam on the opposite side along with a 6 x 8 support post. Secondary beams are 4 x 6 for with 2 x 6 purlins every 30”. All hardware and fasteners are from Simpson’s architectural product line.
Support beam on the opposite side along with a 6 x 8 support post. Secondary beams are 4 x 6 for with 2 x 6 purlins every 30”. All hardware and fasteners are from Simpson’s architectural product line.
0 2026/01/23 18:14:29
0 2026/01/23 18:25:13
Glamour photo of rear axle with completed brake lines.
Glamour photo of rear axle with completed brake lines.
0 2026/01/25 17:26:58
Simpson nailer on left after being cut in half. Finished cable extension on the right.
Simpson nailer on left after being cut in half. Finished cable extension on the right.
0 2026/01/25 17:27:02
Cable extension installed.
Cable extension installed.
0 2026/01/25 17:27:06
0 2026/01/26 16:53:00
New flywheel, clutch and pressure plate installed.
New flywheel, clutch and pressure plate installed.
0 2026/01/27 17:45:34
The lift maxed out just clearing the front end.
The lift maxed out just clearing the front end.
0 2026/01/27 17:45:38
0 2026/01/27 17:45:41
All bolted up.
All bolted up.
0 2026/01/27 17:45:44
0 2026/01/27 17:45:47
Front view of assembly
Front view of assembly
0 2026/01/27 18:56:44
Top view with the back of clutch fork on the left side. The clips have a curly q on one end which fits into a depression in the back side of the fork while the other end wraps around the ear on the clutch collar holding that in place. The clutch bearing (on the right hand side in this pic) is pressed onto the collar with the round face of the bearing facing the engine.
Top view with the back of clutch fork on the left side. The clips have a curly q on one end which fits into a depression in the back side of the fork while the other end wraps around the ear on the clutch collar holding that in place. The clutch bearing (on the right hand side in this pic) is pressed onto the collar with the round face of the bearing facing the engine.
0 2026/01/27 18:56:48
End view
End view
0 2026/01/27 18:56:51
3D view
3D view
0 2026/01/27 18:56:53
0 2026/01/27 18:56:56
Installed.
Installed.
0 2026/01/27 18:56:59
0 2026/01/28 10:02:31
0 2026/01/28 10:02:34
0 2026/01/28 17:21:29
0 2026/01/30 18:52:37
0 2026/01/30 18:52:40
0 2026/01/31 15:29:52
0 2026/01/31 15:29:55
0 2026/01/31 15:29:58
0 2026/02/01 16:59:33
0 2026/02/01 16:59:37
0 2026/02/01 17:05:18
0 2026/02/01 17:05:28
Added piece to each fender to fill the area otherwise occupied by the end caps on the OEM front bumper.
Added piece to each fender to fill the area otherwise occupied by the end caps on the OEM front bumper.
0 2026/02/02 17:32:38
How the areas look with the bumper and filler strip in place.
How the areas look with the bumper and filler strip in place.
0 2026/02/02 17:32:41
Front perspective
Front perspective
0 2026/02/02 17:32:44
0 2026/02/03 16:51:30
The bracket on the left was fabricated specifically for the filler strip and has a capture nut welded on the underside to facilitate ease of filler strip installation.
The bracket on the left was fabricated specifically for the filler strip and has a capture nut welded on the underside to facilitate ease of filler strip installation.
0 2026/02/03 16:51:33