YotaTech Forums
0 2026/02/03 16:51:36
Capture nuts welded on the bumper for the two front mounts.
Capture nuts welded on the bumper for the two front mounts.
0 2026/02/03 16:51:39
Filler strip lined top and bottom just curing. Meanwhile All Star Tug ‘o’ War battle takes place in the background.
Filler strip lined top and bottom just curing. Meanwhile All Star Tug ‘o’ War battle takes place in the background.
0 2026/02/04 17:01:45
Bedside seams cleaned of caulking.
Bedside seams cleaned of caulking.
0 2026/02/04 17:01:49
View from the front
View from the front
0 2026/02/05 16:58:59
0 2026/02/05 16:59:04
The last two joints in the 2” piping need clamps. It’s a very simple exhaust with all straight piping starting at the 4 into 2 section and extending all the way to the 45 elbow and turndown p
The last two joints in the 2” piping need clamps. It’s a very simple exhaust with all straight piping starting at the 4 into 2 section and extending all the way to the 45 elbow and turndown p
0 2026/02/05 16:59:08
Walkers aftermarket equivalent of the OEM muffler bolted right up to the stock hanger.
Walkers aftermarket equivalent of the OEM muffler bolted right up to the stock hanger.
0 2026/02/05 16:59:12
No cat. Tried Walker Mega Clamps on this to save on the welds and they are nice. Stout and clean.
No cat. Tried Walker Mega Clamps on this to save on the welds and they are nice. Stout and clean.
0 2026/02/05 16:59:16
From the front
From the front
0 2026/02/05 17:08:52
One final test fit of the filler.
One final test fit of the filler.
0 2026/02/05 17:08:55
The last two pieces in this photo still need clamps
The last two pieces in this photo still need clamps
0 2026/02/05 17:08:58
Walkers aftermarket equivalent of the OEM muffler bolted right up to the two bolt hanger.
Walkers aftermarket equivalent of the OEM muffler bolted right up to the two bolt hanger.
0 2026/02/05 17:09:01
From the rear axle
From the rear axle
0 2026/02/05 17:09:05
Instrument panel, heater core and new speedometer cable went in today. Feels good to get started on the interior.
Instrument panel, heater core and new speedometer cable went in today. Feels good to get started on the interior.
0 2026/02/08 17:11:17
Current state of the motor install.
Current state of the motor install.
0 2026/02/08 17:11:20
Just verifying no dash pieces are missing. The dash pad came new from a dealer, far left and far right pieces from eBay, middle section from a 3D printer/seller and the glove box came with the truck. SEM paint sounds like it’s pretty good so now it’s time to buy a can and standardize the dash components color.
Just verifying no dash pieces are missing. The dash pad came new from a dealer, far left and far right pieces from eBay, middle section from a 3D printer/seller and the glove box came with the truck. SEM paint sounds like it’s pretty good so now it’s time to buy a can and standardize the dash components color.
0 2026/02/08 17:11:24
View from below looking up at the two slave cylinder lines (marked with blue tape).
View from below looking up at the two slave cylinder lines (marked with blue tape).
0 2026/02/11 17:14:17
Took this bracket off about a month ago when the slave cylinder was replaced and cannot figure out where the heck it bolts to.
Took this bracket off about a month ago when the slave cylinder was replaced and cannot figure out where the heck it bolts to.
0 2026/02/11 17:14:21
View from above looking down at the lines.
View from above looking down at the lines.
0 2026/02/11 17:14:24
0 2026/02/11 17:14:29
Phase 1 of 3 complete.
Phase 1 of 3 complete.
0 2026/02/13 18:06:27
0 2026/02/14 17:17:13
0 2026/02/15 17:45:47
0 2026/02/16 17:27:14
0 2026/02/17 17:17:11
0 2026/02/17 17:39:01
0 2026/02/19 18:42:24
0 2026/02/19 18:42:27
6mm Rivnuts installed in the floor to bolt the console to.
6mm Rivnuts installed in the floor to bolt the console to.
0 2026/02/20 16:54:56
Masked off and ready for SEM paint.
Masked off and ready for SEM paint.
0 2026/02/20 16:54:59
Ready to install.
Ready to install.
0 2026/02/20 16:55:02
What does the flat rod next to the squirrel cage (upper left hand side) do and should something be attached to it?
What does the flat rod next to the squirrel cage (upper left hand side) do and should something be attached to it?
0 2026/02/22 18:00:43
Is there supposed to be a piece of flex ductwork from the squirrel cage to the white box on the right hand side? They’re both the same diameter at just a little over 4” and is that all that’s missing?
Is there supposed to be a piece of flex ductwork from the squirrel cage to the white box on the right hand side? They’re both the same diameter at just a little over 4” and is that all that’s missing?
0 2026/02/22 18:00:46
Silver Metallic hockey stick design
Silver Metallic hockey stick design
0 2026/02/23 19:30:39
0 2026/02/26 05:01:18
0 2026/02/26 05:01:21
Got started with the polishing on the right front fender.
Got started with the polishing on the right front fender.
0 2026/02/26 18:32:21
Here’s the Kovax system. The sanding blocks are very small and the paper is precut to fit each block. There is a small curved block (not shown) and a Tolecard which has the size and flexibility of a playing card so it works best on most of the body panel curves.
Here’s the Kovax system. The sanding blocks are very small and the paper is precut to fit each block. There is a small curved block (not shown) and a Tolecard which has the size and flexibility of a playing card so it works best on most of the body panel curves.
0 2026/02/26 18:33:54
0 2026/02/27 18:50:05