YotaTech Forums
0 2024/01/28 10:00:53
Top view of the latch just before it engages the catch. Getting the catch tab to just the right length was the trickiest part as I recall.
Top view of the latch just before it engages the catch. Getting the catch tab to just the right length was the trickiest part as I recall.
0 2024/01/28 10:00:56
0 2025/01/11 02:49:51
0 2025/01/11 02:49:54
0 2025/01/11 02:49:56
0 2025/01/11 02:49:59
0 2025/01/14 05:04:04
0 2025/01/14 05:04:07
0 2025/01/14 20:29:24
0 2025/01/14 20:29:27
0 2025/01/14 20:29:29
Small spring bump stops or pads. Not sure what they’re called.
Small spring bump stops or pads. Not sure what they’re called.
0 2025/01/15 17:19:34
Torque rod installed.
Torque rod installed.
0 2025/01/15 17:19:38
0 2025/01/15 21:05:29
0 2025/01/15 21:05:32
0 2025/01/15 21:05:35
Check out the wear on these two spring backed pieces that sit on either side of the knuckle arm ball inside the drag link. The same pieces on the pitman arm end show very little wear.
Check out the wear on these two spring backed pieces that sit on either side of the knuckle arm ball inside the drag link. The same pieces on the pitman arm end show very little wear.
0 2025/01/15 21:12:22
Torque rod installed
Torque rod installed
0 2025/01/15 21:12:24
0 2025/01/15 21:12:27
0 2025/01/18 01:36:37
0 2025/01/18 01:36:39
Before pic of the area
Before pic of the area
0 2025/01/29 02:30:46
After welding in a patch panel and some bondo
After welding in a patch panel and some bondo
0 2025/01/29 02:30:49
Fender wells repainted with some bed liner spray
Fender wells repainted with some bed liner spray
0 2025/01/29 02:30:52
0 2025/01/29 02:30:54
0 2025/02/06 18:37:16
0 2025/02/06 18:37:19
0 2025/02/06 18:37:22
0 2025/02/06 18:37:24
0 2025/02/10 17:23:47
0 2025/02/10 17:23:50
0 2025/02/10 17:23:52
Removing the fuel filler steel hose section was a bear. All three screws needed to be drilled out. I think they’ll get replaced with stainless Allen screws or hex bolts.
Removing the fuel filler steel hose section was a bear. All three screws needed to be drilled out. I think they’ll get replaced with stainless Allen screws or hex bolts.
0 2025/02/13 17:17:53
0 2025/02/13 17:17:56
Found a spot of rust just above the fuel filler door so I cut that out and installed a small patch panel.
Found a spot of rust just above the fuel filler door so I cut that out and installed a small patch panel.
0 2025/02/13 17:17:58
Discovered yet more rust under the ‘O’ in Toyota, cut it out and installed an additional patch panel.
Discovered yet more rust under the ‘O’ in Toyota, cut it out and installed an additional patch panel.
0 2025/02/13 17:18:00
0 2025/02/14 03:25:27
0 2025/02/16 04:19:14
0 2025/02/16 04:19:16
Pre treatment
Pre treatment
0 2025/02/16 04:35:31