rattlewagon's 1992 Pickup Build-Up Thread
#561
Registered User
Thread Starter
Parts came in!
They came pre ground for the 4.7 gears, which is sweet.
temporary_zps42e7ea4d.jpg?t=1423535633
Why they need to be ground down, and why Im glad they came that way.
temporary_zpsea61414e.jpg?t=1423535640
temporary_zps3d85ef55.jpg?t=1423535640
temporary_zps3069c2cd.jpg?t=1423535640
And... All back together!
temporary_zps9a0772c2.jpg?t=1423535640
They came pre ground for the 4.7 gears, which is sweet.
temporary_zps42e7ea4d.jpg?t=1423535633
Why they need to be ground down, and why Im glad they came that way.
temporary_zpsea61414e.jpg?t=1423535640
temporary_zps3d85ef55.jpg?t=1423535640
temporary_zps3069c2cd.jpg?t=1423535640
And... All back together!
temporary_zps9a0772c2.jpg?t=1423535640
#563
Registered User
Thread Starter
THanks! The instructions were great, very clear, and I bagged and labeled evrything when I took it apart, which made the rebuild that much easier. Well see if the internet was right when we go to see if everything lines up.
#565
Registered User
Thread Starter
Out with the old
temporary_zps7f140d95.jpg?t=1424144169
We lifted and test fit the case maybe 6 times through out the day. Parts of the tail housing of the r150f need to be trimmed, shifter hole needs to be opened up a little. Once was because this tab was hanging up the 2/4wd shift rail on the trans, even through it looks like it would work.
temporary_zps399e21e6.jpg?t=1424144494
The biggest issue that is temporarly solved is that the shifters hit. A lot.
temporary_zps9af6fde2.jpg?t=1424144498
The hi/low shifter needs to be in the forward position, which doesnt allow me to go over into 3rd. We heat and bent the shifter a few times and got it to fit without the knob on the hi/low shifter. Im going to make a small plate that sits on top of the shifter where the knob would be and its just going to re locate the knob about 2" back.
temporary_zps92045e92.jpg?t=1424144787
Heres a shot of the plate and where I had to grind the tail housing of the r150f so the bolt heads will fit. Ill admit, I got a little carrier away on the right side, but there wasnt that much there to begin with. Haha.
temporary_zpsd48eebe9.jpg?t=1424145737
The back of the case with the new tg mount. The internet was right, it all lines up. But the input and out put of the case are now about an inch back from stock. The front DS had plenty of slip so no big hot dog there, but in the back I needed to re drill holes and move the carrier bearing back. The case now sits almost entirely up above the skid plate, where as the v6 case hung down, so ill be modifying the skid part of the plate to be flatter.
temporary_zps4f964c66.jpg?t=1424145781
Last thing, is its puking gear oil from somewhere. I havent really had time to look yet as Ive only driven it twice very quickly in the dark, but I hope I dont have to pull it back apart to re seal it.
Last notes, I did not hook up the spedo, as the truck is a electronic and the t case is cable. They make adapters, but I dont care its a trail rig. Same goes with the 4x4 light. The 2 wires on my sensor fell off long ago, and the new case only has 1 wire, so I just put a bolt in that hole.
Put the fender back on and took a few glam shots of my custom body work.
temporary_zps79c37baf.jpg?t=1424144839
temporary_zps792317a7.jpg?t=1424144839
temporary_zpsdcedd630.jpg?t=1424144839
temporary_zps4b4cefe4.jpg?t=1424144839
temporary_zps25e58608.jpg?t=1424145461
The gearing is great, but its not "marlin crawler low", but should work great for the bashing that I do. Crawl ratio before was around 40, now its 80. Adding another case to this combo would make it about 180.
temporary_zps7f140d95.jpg?t=1424144169
We lifted and test fit the case maybe 6 times through out the day. Parts of the tail housing of the r150f need to be trimmed, shifter hole needs to be opened up a little. Once was because this tab was hanging up the 2/4wd shift rail on the trans, even through it looks like it would work.
temporary_zps399e21e6.jpg?t=1424144494
The biggest issue that is temporarly solved is that the shifters hit. A lot.
temporary_zps9af6fde2.jpg?t=1424144498
The hi/low shifter needs to be in the forward position, which doesnt allow me to go over into 3rd. We heat and bent the shifter a few times and got it to fit without the knob on the hi/low shifter. Im going to make a small plate that sits on top of the shifter where the knob would be and its just going to re locate the knob about 2" back.
temporary_zps92045e92.jpg?t=1424144787
Heres a shot of the plate and where I had to grind the tail housing of the r150f so the bolt heads will fit. Ill admit, I got a little carrier away on the right side, but there wasnt that much there to begin with. Haha.
temporary_zpsd48eebe9.jpg?t=1424145737
The back of the case with the new tg mount. The internet was right, it all lines up. But the input and out put of the case are now about an inch back from stock. The front DS had plenty of slip so no big hot dog there, but in the back I needed to re drill holes and move the carrier bearing back. The case now sits almost entirely up above the skid plate, where as the v6 case hung down, so ill be modifying the skid part of the plate to be flatter.
temporary_zps4f964c66.jpg?t=1424145781
Last thing, is its puking gear oil from somewhere. I havent really had time to look yet as Ive only driven it twice very quickly in the dark, but I hope I dont have to pull it back apart to re seal it.
Last notes, I did not hook up the spedo, as the truck is a electronic and the t case is cable. They make adapters, but I dont care its a trail rig. Same goes with the 4x4 light. The 2 wires on my sensor fell off long ago, and the new case only has 1 wire, so I just put a bolt in that hole.
Put the fender back on and took a few glam shots of my custom body work.
temporary_zps79c37baf.jpg?t=1424144839
temporary_zps792317a7.jpg?t=1424144839
temporary_zpsdcedd630.jpg?t=1424144839
temporary_zps4b4cefe4.jpg?t=1424144839
temporary_zps25e58608.jpg?t=1424145461
The gearing is great, but its not "marlin crawler low", but should work great for the bashing that I do. Crawl ratio before was around 40, now its 80. Adding another case to this combo would make it about 180.
#567
Registered User
I haven't checked your thread in a while, you've been busy! the t-case gears will be sweet! your brave tackling the t-case rebuild, gears scare me!
Regarding your shifter clearance issue, maybe a short throw kit is in order?
Regarding your shifter clearance issue, maybe a short throw kit is in order?
Last edited by liveoffroad; 02-25-2015 at 06:07 AM.
#569
Registered User
Join Date: Aug 2011
Location: blind river, ON
Posts: 81
Likes: 0
Received 0 Likes
on
0 Posts
Looking good, really like the way this build has transformed over the years. those 4.7 gears look awesome, can't imagine the whiplash when you touch the pedal!
#570
Registered User
Thread Starter
Next winter when the 4.3 goes in, I plan to switch to an auto, so I dont really want to put any money into the r150f that I dont need to, and I have it workable right now.
Gears were a piece of cake, nothing to be afraid of!
Thanks! It pretty fun to rip through the 5 speeds!
#572
Contributing Member
iTrader: (1)
Rattlewagon, truck is turning out real nice, its always been one of my favs on this site, and its turning into a paintless dent guys wet dream.
#573
Registered User
iTrader: (5)
Dude, I was reading how you said the shifters hit. I was going to add, just wait till you get out there and start twisting, they will rip that trans tunnel wide open. I'm sure you've already realize this and just kept cutting to fit, but I'm just letting you know, in case you haven't pushed it hard, when that stuff starts twisting, it really works on the tunnel. obviously mine is all filled up and insulated and with the original trans shifter bezel and everything, so it's probably a little more of a pain in the ass because I want it to look perfect... Okay I want it to look decent. Haha. But it's just a heads up. I'm working on coming up with something that I can weld too the shifter plates so that I can turn this into a swing under instead of swing over triple shifter that I have. I love having it! Just need to get its wing I understand that I can drop the body lift! Lol
#574
Registered User
Thread Starter
Johnny boy- me either, but that was the first thing that came up when I googled it.
Thanks chef and mr woods!
Oh shes been pushed and twisted plenty. I ripped a motor mount in half last spring, so now they are through bolted marlin style, which only allows so much twisting. And with this new t case, I have the TG heavy duty mount which will also cut down on twisting. I had to open up the tunnel hole anyway for the new case and twin sticks so I made sure to cut a little extra. No boot or bezel over the hole, just going to leave it open for simplicity. Plus I paid good money for the adapter plate, I want to look at it. Haha.
Motor mount fix here: https://www.yotatech.com/forums/f199...l#post52191572
Thanks chef and mr woods!
Oh shes been pushed and twisted plenty. I ripped a motor mount in half last spring, so now they are through bolted marlin style, which only allows so much twisting. And with this new t case, I have the TG heavy duty mount which will also cut down on twisting. I had to open up the tunnel hole anyway for the new case and twin sticks so I made sure to cut a little extra. No boot or bezel over the hole, just going to leave it open for simplicity. Plus I paid good money for the adapter plate, I want to look at it. Haha.
Motor mount fix here: https://www.yotatech.com/forums/f199...l#post52191572
Last edited by rattlewagon; 03-28-2015 at 06:14 PM.
#575
Registered User
#578
Registered User
Thread Starter
Thanks guys!
Got up into the woods a bit today, but it was slow going. Still about a foot and half of snow that starting to melt out, making it very soft. Headed back to deal with some engine oil leaks. Rear cam seal on the pass side and dist o ring should seal it up.
Got up into the woods a bit today, but it was slow going. Still about a foot and half of snow that starting to melt out, making it very soft. Headed back to deal with some engine oil leaks. Rear cam seal on the pass side and dist o ring should seal it up.
Last edited by rattlewagon; 03-29-2015 at 04:05 PM.
#579
Registered User
Thread Starter
My rear cam cover was the cause of the oil leak.. but the cam bearings didnt look too hot. Guess I better get movin on prepin the 4.3 to go in.
yikes. Big old glob of assembly lube and a prayer and awaay we go..
yikes. Big old glob of assembly lube and a prayer and awaay we go..
Last edited by rattlewagon; 03-29-2015 at 04:06 PM.
#580
Registered User
Thread Starter
Made a little cart to move the 4.3 around on and pulled it out of the corner. Time to start causally working on this guy.
Made a few new climbs over the weekend, shooting to have a trail ride here mid may.
My strange no hot start is still lurking. Truck starts fine every time cold. And if I shut it off and turn it back on with in 5 min, starts no problem. But if is sits 10-20 min and I try it, It acts like its out of gas. But it is getting gas. Something wrong on the spark end. Has good plugs/wires with a new coil that I thought was the problem. Grounds are good. Its getting spark, but is weak. I need to get a volt meter on the igniter and distributor I guess.
Made a few new climbs over the weekend, shooting to have a trail ride here mid may.
My strange no hot start is still lurking. Truck starts fine every time cold. And if I shut it off and turn it back on with in 5 min, starts no problem. But if is sits 10-20 min and I try it, It acts like its out of gas. But it is getting gas. Something wrong on the spark end. Has good plugs/wires with a new coil that I thought was the problem. Grounds are good. Its getting spark, but is weak. I need to get a volt meter on the igniter and distributor I guess.