piston ring dumb question!
Jun 20, 2008 | 05:54 PM
#24
Thread Starter
Registered User
Joined: Feb 2008
Posts: 2,799
Likes: 3
From: oregon
only thing good about it is the store "davy jones locker". its the only place you can get hard a when every other liquor store is closed lol.
Jun 20, 2008 | 06:27 PM
#27
Registered User
Joined: Feb 2008
Posts: 2,805
Likes: 1
From: Salem, OR
LOL...that is like the coolest store ever! I've been to that store at least a hundred times. I used to camp at Bastendorf...pretty cool campground.
Jun 21, 2008 | 04:59 AM
#30
Registered User
Joined: Sep 2005
Posts: 8,656
Likes: 16
From: NW Ark on wooded ten acres...Ozarks at large!
<redneck> Ugh.....did somebody say "thread-jack"?!
I got'chur thread-jack....jack!! Don't git me started!!! Whoooyeah!!! Texas Can'o Whoop@#$!!! I'm comin' home!! Whooooeeee!! (Freebird on air guitar) D'ats what I'm talkin' bout!!!!
I got'chur thread-jack....jack!! Don't git me started!!! Whoooyeah!!! Texas Can'o Whoop@#$!!! I'm comin' home!! Whooooeeee!! (Freebird on air guitar) D'ats what I'm talkin' bout!!!!
Jun 22, 2008 | 06:46 AM
#32
Registered User
Joined: Jul 2005
Posts: 554
Likes: 2
From: Manassas, VA
I'm going to guess that the way you broke the ring was trying to spin it on by hand.
Using this method is very risky and likely to break at least one ring.
Problem is that you can't see that you've deformed some or all of the others, possibly to the point that they will break in service.
If you did use this method I would strongly recommend getting the proper ring spreading tool and use it.
And always check the ring gaps.
Using this method is very risky and likely to break at least one ring.
Problem is that you can't see that you've deformed some or all of the others, possibly to the point that they will break in service.
If you did use this method I would strongly recommend getting the proper ring spreading tool and use it.
And always check the ring gaps.
Jun 22, 2008 | 10:09 AM
#33
Registered User
Joined: Sep 2005
Posts: 8,656
Likes: 16
From: NW Ark on wooded ten acres...Ozarks at large!
Jun 22, 2008 | 11:14 AM
#34
Thread Starter
Registered User
Joined: Feb 2008
Posts: 2,799
Likes: 3
From: oregon
I'm going to guess that the way you broke the ring was trying to spin it on by hand.
Using this method is very risky and likely to break at least one ring.
Problem is that you can't see that you've deformed some or all of the others, possibly to the point that they will break in service.
If you did use this method I would strongly recommend getting the proper ring spreading tool and use it.
And always check the ring gaps.
Using this method is very risky and likely to break at least one ring.
Problem is that you can't see that you've deformed some or all of the others, possibly to the point that they will break in service.
If you did use this method I would strongly recommend getting the proper ring spreading tool and use it.
And always check the ring gaps.
Jun 22, 2008 | 11:16 AM
#35
Thread Starter
Registered User
Joined: Feb 2008
Posts: 2,799
Likes: 3
From: oregon
Thread
Thread Starter
Forum
Replies
Last Post
