YotaTech Forums
sits a bit high
sits a bit high
0 2021/11/15 08:14:31
will need to adjust the mounting holes - the old frame was more bent/twisted, so the mounting locations on this excellent frame do not match the holes in the body. fortunately, fiberglass is easy to drill, and repair/fill.
will need to adjust the mounting holes - the old frame was more bent/twisted, so the mounting locations on this excellent frame do not match the holes in the body. fortunately, fiberglass is easy to drill, and repair/fill.
0 2021/11/15 08:14:46
pulled the old motor
pulled the old motor
0 2022/02/10 03:45:50
that’ll buff out, right?
that’ll buff out, right?
0 2022/02/10 03:46:33
back on the road
back on the road
0 2022/02/10 03:47:33
from my "older" '87
from my "older" '87
0 2022/03/09 07:06:19
from my "newer" '87
from my "newer" '87
0 2022/03/09 07:07:02
0 2022/03/14 17:06:33
the original buckets in my '87 4runner
the original buckets in my '87 4runner
0 2022/03/31 17:13:39
the sport buckets that i swapped into my '87, here in my '88 parts runner
the sport buckets that i swapped into my '87, here in my '88 parts runner
0 2022/03/31 17:14:43
0 2022/03/31 17:20:13
0 2022/04/10 18:51:24
0 2022/04/10 18:52:21
0 2022/04/30 17:50:35
0 2022/04/30 17:50:45
0 2022/04/30 17:51:21
0 2022/04/30 17:51:29
0 2022/05/15 08:03:25
0 2022/06/01 17:23:19
0 2022/06/01 17:23:35
0 2022/06/01 17:24:20
looks about right
looks about right
0 2022/06/06 17:51:26
still have a few things to attach
still have a few things to attach
0 2022/06/06 17:51:38
need to finish attaching the fenders to the tub
need to finish attaching the fenders to the tub
0 2022/06/06 17:51:59
will need to trim the bumper mounting tabs, too
will need to trim the bumper mounting tabs, too
0 2022/06/06 17:52:48
0 2022/06/16 06:30:26
0 2022/06/16 06:30:51
0 2022/06/16 06:31:05
0 2022/06/16 06:31:26
0 2022/06/16 06:31:38
0 2022/06/16 06:31:50
the locking hub cover and the six 6mm allen head bolts
the locking hub cover and the six 6mm allen head bolts
0 2022/06/26 11:44:37
so, i'm showing the "process" on some spare parts, because i didn't take pictures when doing the work...this is the locking hub cover, with the hub body below it
so, i'm showing the "process" on some spare parts, because i didn't take pictures when doing the work...this is the locking hub cover, with the hub body below it
0 2022/06/26 11:45:15
hub cover removed. on the spindle installed, you'd see the end of the stub axle and the "gold" 12mm bolt in the center here. remove the bolt.
hub cover removed. on the spindle installed, you'd see the end of the stub axle and the "gold" 12mm bolt in the center here. remove the bolt.
0 2022/06/26 11:47:11
the recess in the hub body where the cone washers seat and the wheel hub studs protrude. the locking hub body is secured to the wheel hub via the cone wasers with the studs running throgh them, and then a lockwasher and nut (12mm) on each of the six
the recess in the hub body where the cone washers seat and the wheel hub studs protrude. the locking hub body is secured to the wheel hub via the cone wasers with the studs running throgh them, and then a lockwasher and nut (12mm) on each of the six
0 2022/06/26 11:49:46
the snap ring that holds the brake portion of the locking hub system to the stub axle. use a small flat-blade screwdriver to pry this off of the stub axle
the snap ring that holds the brake portion of the locking hub system to the stub axle. use a small flat-blade screwdriver to pry this off of the stub axle
0 2022/06/26 11:51:56
this is what you'll see when the locking hub body is removed. this brake assembly rests within the wheel hub. imagine that the stub axle and spindle shaft are protruding through the center. you have removed the stub axle snap ring
this is what you'll see when the locking hub body is removed. this brake assembly rests within the wheel hub. imagine that the stub axle and spindle shaft are protruding through the center. you have removed the stub axle snap ring
0 2022/06/26 11:53:27
the snap ring/lock ring that holds the brake band mechanism within the bearing retainer lock plate
the snap ring/lock ring that holds the brake band mechanism within the bearing retainer lock plate
0 2022/06/26 11:56:12
another view with the lock ring/snap ring still installed. this is the lock plate, brake spring, brake spring cover, and below is the 54mm wheel bearing nut
another view with the lock ring/snap ring still installed. this is the lock plate, brake spring, brake spring cover, and below is the 54mm wheel bearing nut
0 2022/06/26 11:58:59
the brake spring assembly, encased by plastic/bakelite. it is two pieces. this is the "bottom" side, with one piece of the plastic removed.
the brake spring assembly, encased by plastic/bakelite. it is two pieces. this is the "bottom" side, with one piece of the plastic removed.
0 2022/06/26 12:00:33