How hard is it to pull this off?
#1
Registered User
Thread Starter
Join Date: Mar 2008
Location: Lewiston, Idaho
Posts: 582
Likes: 0
Received 0 Likes
on
0 Posts
How hard is it to pull this off?
There is a plate on the back of the head for the egr on a 22re how hard is it to pull off while in the truck?
#2
Registered User
Join Date: Jan 2007
Location: milwaukee, WI baby muddin in the streets!!
Posts: 2,801
Likes: 0
Received 1 Like
on
1 Post
when its in the truck??? why whats wrong with it? are doing a egr block off???
if your doing a egr block off then just block it off at the intake
i guess i just dont get it anymore info on what your trying to do here?
if your doing a egr block off then just block it off at the intake
i guess i just dont get it anymore info on what your trying to do here?
#3
Registered User
Thread Starter
Join Date: Mar 2008
Location: Lewiston, Idaho
Posts: 582
Likes: 0
Received 0 Likes
on
0 Posts
nope not trying to block it off! Have egr code 71! Egr is good Tvv for egr is also good. There is a blockage some were between the egr and my header! I have tested and retesed everthing so Im down to seeing if mabey the gasket on that plate is fliped and causing no flow or mabye its my header? Not to sure at this point!
#4
Registered User
Join Date: Oct 2007
Location: near Redding California
Posts: 297
Likes: 0
Received 0 Likes
on
0 Posts
Get prepared to pull the head! The blockage is probably in the passage on the driver's side of the head, leading to the exhaust ports. Clearing this clog will require the vigorous use of a coat hanger or brazing rod; not easily achieved without removal of the head.
At least, that was my experience.
At least, that was my experience.
#5
Registered User
Join Date: Jan 2007
Location: milwaukee, WI baby muddin in the streets!!
Posts: 2,801
Likes: 0
Received 1 Like
on
1 Post
well its a pain in the rump but yes anythings posible i guess to make it a lil easier you might wanna pull the valve cover off and take the 4 10mm bolts out i thing thats the size that or 12mm maybe even 14mm cant remember when i took mine off and then pry it off but its going to be really hard you know
#7
Registered User
Thread Starter
Join Date: Mar 2008
Location: Lewiston, Idaho
Posts: 582
Likes: 0
Received 0 Likes
on
0 Posts
thanks guys there isent any blockage cuz the engine in new only like 1600 miles on it but i think my dumb a@@ put the gasket on backwards so it is blocking that hole off for egr flow on the plate on the back of the head! Wish me luck im going to try it with out pulling the head! Also do you guys think it could be my pacesetter header mabye isent alowing flow threw that port?
Trending Topics
#8
Registered User
Join Date: Jul 2007
Location: Richmond va
Posts: 739
Likes: 0
Received 0 Likes
on
0 Posts
Check the Egr temp sensor,If you had it out and cleaned it,this may be your problem.Also if you gutted the cat this can cause it also.See the post for putting in a 10 ohm resistor,this will keep the code from coming up.
#9
Registered User
Thread Starter
Join Date: Mar 2008
Location: Lewiston, Idaho
Posts: 582
Likes: 0
Received 0 Likes
on
0 Posts
ok ive done all of that! I cant blow air threw the plate on the back of the head! I blow were the egr is threw the head and its clogged somewere from the egr to the header! So I guess I will have to try and pull the plate off the back! Just dont want to pull the the head off but might have to! I have tested the egr temp sensor and its good!
Thread
Thread Starter
Forum
Replies
Last Post
djpg2000
Tires & Wheels
11
11-11-2020 04:56 AM
Iceman4193
86-95 Trucks & 4Runners
3
07-15-2015 04:48 PM
skoti89
Offroad Tech
3
07-08-2015 12:05 AM