Ooooo ok I get it now...

Show us!!! I got some pic's I gotta post of the truck and runner. I'll try and get them up later today. I am at work you know.

 

ha i never have much luck with the old lady helping me she has more questions than a 4 year old he he i dont get much done that way did you buy the flowers yat so she dont drop the jack down on ya he he

 

just fired her.

 

ha yeppers heck i aint doing anything ill jus hop in the truck and head up there and run the jack for ya he he

 

Ditto with the wife helping out. It always seams easier to have her help until she does and like previously posted more questions than a hiper active four year old. On top of the fact that i can't even ask her to hand me tools. By the time i get done explaining what the tool is and why i need it it would take less time and hassle to just go get it myself. There's a nice unwritten rule between us that if i'm in the garage working it's guy time out there. I'm still secretly jellious of you guys that have girls that will help out and understand whats going on.

 

.

Pick me up on the way!!!

I keep threatening him on stoppin in.

 

ha we should i could grab ya and head up there and getter done but his satisfaction and doing the man roar when you concer your task would be taken away and no tarazan yell would happen he he. and yes my shay knows tools but always wonders why i didnt do something this way or wouldnt it be easier if you did this blahblah etc etc god love her

 

me: Ok I really need you to do the jack

Her: no, your're gonna say i did it wrong or the trck is gonna fall over and crush you

me: it's on stands, it can't fall over from you doing that

her:well, what then?

me: here, i'll put this brick under the jack and i'll show you how to work this

her: this is stupid, wait for Joe

me: I can't yell at Joe, he'll never help me again

and commenced to showing her sevearl times how to release it / tighten it and raise it too.

plan was .....release the handle let the diff lower, tighten the handle, jack it to keep it still...while i release the bottle jack


anyway, all went well, nobody was hurt.

her:am i done?

me: yes, now leave me out here.

 

how it was supported



I did take a pic of the jack operator, but since i value my life somewhat, it will not be posted.

 

how important is this?


i know it goes here, and it's definitely going in AFTER the pan is on

 

block is scraped and ready.

gonna do the dry fit thing

 

You need that to keep crap outta your bell housing!

 

You're a brave man.

Clearly you've never seen jack stands kick out though, because I can assure you it does happen, even on level ground. If it weren't for the fact I had the rear of my truck up on two sets of stands it'd be on the ground right now as a result of me trying to hammer out the leaf hanger bolts.

 

I kinda think you need to put that back...

Glad to hear your helper work out...better than mine.

 

FAILBOAT is circling................


nice paint-job on the pan is all scraped up ...still just trying to get the pan to lay just under where it needs to be.

took a 4.5 minute break, looked at things. passenger's side body mount for the diff is bound.....gave it a push with my foot, worked the jack a little, gained about 1 more inch....i think that may be enough.

oh yeah...readers......do NOT put your steering dampener on BEFORE putting the pan back on, it WILL get in your way.

 

and yes, i have the diff covered with a beach towel to prevent scraping....so, that was useless.

 

Not like anyone is gonna get a good look under there anyways! Just hand one of your kids the paint and a small brush once it's all done and on to do some touch-ups.

 

OK...that was the stuff!!!!!


uptake tube is on....have to torque them to 9ft/lbs....i'm impressed i didn't drop any friggin screws in it and have to take it off again.

 

pics in about 10 minutes.

 

Good deal man good deal...I'm getting goose bumps!!!