YotaTech Forums
1/4” birch wrapped with an old piece of marine grade vinyl that was laying around from a previous project.
1/4” birch wrapped with an old piece of marine grade vinyl that was laying around from a previous project.
0 2026/03/03 18:01:16
Still haven’t decided what to do with the shifter boots.
Still haven’t decided what to do with the shifter boots.
0 2026/03/03 18:01:13
Hey Disco the carpet was oversized about 4” lengthwise and width wise. It went in fairly well with the only problem area being the wrinkle about 6” in front of the shifters. I think the console is going to cover that.
Hey Disco the carpet was oversized about 4” lengthwise and width wise. It went in fairly well with the only problem area being the wrinkle about 6” in front of the shifters. I think the console is going to cover that.
0 2026/03/02 16:59:57
And a Stubby antennae!
And a Stubby antennae!
0 2026/03/01 17:22:09
0 2026/02/28 17:06:24
0 2026/02/28 17:06:20
0 2026/02/27 22:04:40
0 2026/02/27 18:50:08
0 2026/02/27 18:50:05
Here’s the Kovax system. The sanding blocks are very small and the paper is precut to fit each block. There is a small curved block (not shown) and a Tolecard which has the size and flexibility of a playing card so it works best on most of the body panel curves.
Here’s the Kovax system. The sanding blocks are very small and the paper is precut to fit each block. There is a small curved block (not shown) and a Tolecard which has the size and flexibility of a playing card so it works best on most of the body panel curves.
0 2026/02/26 18:33:54
Got started with the polishing on the right front fender.
Got started with the polishing on the right front fender.
0 2026/02/26 18:32:21
0 2026/02/26 05:01:21
0 2026/02/26 05:01:18
Silver Metallic hockey stick design
Silver Metallic hockey stick design
0 2026/02/23 19:30:39
Is there supposed to be a piece of flex ductwork from the squirrel cage to the white box on the right hand side? They’re both the same diameter at just a little over 4” and is that all that’s missing?
Is there supposed to be a piece of flex ductwork from the squirrel cage to the white box on the right hand side? They’re both the same diameter at just a little over 4” and is that all that’s missing?
0 2026/02/22 18:00:46
What does the flat rod next to the squirrel cage (upper left hand side) do and should something be attached to it?
What does the flat rod next to the squirrel cage (upper left hand side) do and should something be attached to it?
0 2026/02/22 18:00:43
Ready to install.
Ready to install.
0 2026/02/20 16:55:02
Masked off and ready for SEM paint.
Masked off and ready for SEM paint.
0 2026/02/20 16:54:59
6mm Rivnuts installed in the floor to bolt the console to.
6mm Rivnuts installed in the floor to bolt the console to.
0 2026/02/20 16:54:56
0 2026/02/19 18:42:27
0 2026/02/19 18:42:24
0 2026/02/17 17:39:01
0 2026/02/17 17:17:11
0 2026/02/16 17:27:14
0 2026/02/15 17:45:47
0 2026/02/14 17:17:13
Phase 1 of 3 complete.
Phase 1 of 3 complete.
0 2026/02/13 18:06:27
0 2026/02/11 17:14:29
View from above looking down at the lines.
View from above looking down at the lines.
0 2026/02/11 17:14:24
Took this bracket off about a month ago when the slave cylinder was replaced and cannot figure out where the heck it bolts to.
Took this bracket off about a month ago when the slave cylinder was replaced and cannot figure out where the heck it bolts to.
0 2026/02/11 17:14:21
View from below looking up at the two slave cylinder lines (marked with blue tape).
View from below looking up at the two slave cylinder lines (marked with blue tape).
0 2026/02/11 17:14:17
Just verifying no dash pieces are missing. The dash pad came new from a dealer, far left and far right pieces from eBay, middle section from a 3D printer/seller and the glove box came with the truck. SEM paint sounds like it’s pretty good so now it’s time to buy a can and standardize the dash components color.
Just verifying no dash pieces are missing. The dash pad came new from a dealer, far left and far right pieces from eBay, middle section from a 3D printer/seller and the glove box came with the truck. SEM paint sounds like it’s pretty good so now it’s time to buy a can and standardize the dash components color.
0 2026/02/08 17:11:24
Current state of the motor install.
Current state of the motor install.
0 2026/02/08 17:11:20
Instrument panel, heater core and new speedometer cable went in today. Feels good to get started on the interior.
Instrument panel, heater core and new speedometer cable went in today. Feels good to get started on the interior.
0 2026/02/08 17:11:17
From the rear axle
From the rear axle
0 2026/02/05 17:09:05
Walkers aftermarket equivalent of the OEM muffler bolted right up to the two bolt hanger.
Walkers aftermarket equivalent of the OEM muffler bolted right up to the two bolt hanger.
0 2026/02/05 17:09:01
The last two pieces in this photo still need clamps
The last two pieces in this photo still need clamps
0 2026/02/05 17:08:58
One final test fit of the filler.
One final test fit of the filler.
0 2026/02/05 17:08:55
From the front
From the front
0 2026/02/05 17:08:52
No cat. Tried Walker Mega Clamps on this to save on the welds and they are nice. Stout and clean.
No cat. Tried Walker Mega Clamps on this to save on the welds and they are nice. Stout and clean.
0 2026/02/05 16:59:16