YotaTech Forums
All these parts except the snap ring come in the kit.
All these parts except the snap ring come in the kit.
0 2021/08/22 19:24:48
Gotta reuse this snap ring!
Gotta reuse this snap ring!
0 2021/08/22 19:24:54
Cleaned up on wire wheel.
Cleaned up on wire wheel.
0 2021/08/22 19:25:01
Teflon seal is easier to place if you bend it into a cardioid shape.
Teflon seal is easier to place if you bend it into a cardioid shape.
0 2021/08/22 19:28:45
Teflon seal goes inside o-ring.
Teflon seal goes inside o-ring.
0 2021/08/22 19:28:53
1 1/4 socket is good for pushing down the seal. I also cleaned the sector shaft surface where this seal contacts it using a scuff pad and Wd40.
1 1/4 socket is good for pushing down the seal. I also cleaned the sector shaft surface where this seal contacts it using a scuff pad and Wd40.
0 2021/08/22 19:29:02
Lightly grease the power piston cylinder and o-rings and use two bolts to pull it until is seats. Then use the input shaft to center the gear teeth on the piston to the middle of its travel. The input shaft turns about 4.5 rotations so put it at 2.25 and you should be right about there. The flattend area on the input splines will be on the bottom if looking at the box in mounted position.
Lightly grease the power piston cylinder and o-rings and use two bolts to pull it until is seats. Then use the input shaft to center the gear teeth on the piston to the middle of its travel. The input shaft turns about 4.5 rotations so put it at 2.25 and you should be right about there. The flattend area on the input splines will be on the bottom if looking at the box in mounted position.
0 2021/08/22 19:36:03
Grease the teeth on the power piston and sector shaft and where the seal rides on the shaft. Now center the sector shaft teeth and drop it in. Turn the box upside down and allow its own weight to push it in.
Grease the teeth on the power piston and sector shaft and where the seal rides on the shaft. Now center the sector shaft teeth and drop it in. Turn the box upside down and allow its own weight to push it in.
0 2021/08/22 19:45:46
0 2021/08/22 19:45:56
0 2021/08/22 19:56:11
Yes, I had to take the power piston out and bearing shell off again. Grrrr.
Yes, I had to take the power piston out and bearing shell off again. Grrrr.
0 2021/08/22 19:57:50
0 2021/08/29 21:04:39
0 2021/08/29 21:04:52
0 2021/09/06 18:06:48
If i was a mouse, you bet i would live in a Jag.
If i was a mouse, you bet i would live in a Jag.
0 2021/09/06 18:06:57
0 2021/09/06 18:07:02
MGA
MGA
0 2021/09/06 18:19:47
Circa 79 Datsun
Circa 79 Datsun
0 2021/09/06 18:19:56
0 2021/09/06 18:20:07
0 2021/09/06 18:20:13
0 2021/09/06 18:20:23
MGA
MGA
0 2021/09/06 18:23:10
Circa 1979 Datsun. A rare car these days.
Circa 1979 Datsun. A rare car these days.
0 2021/09/06 18:23:20
0 2021/09/06 18:23:30
0 2021/09/06 18:23:39
Monument in Salem.
Monument in Salem.
0 2021/09/06 18:23:45
The famous Witch Museum.
The famous Witch Museum.
0 2021/09/06 18:23:52
It is actually worth the wait.
It is actually worth the wait.
0 2021/09/06 18:24:01
0 2021/09/06 18:24:09
Eat clams. Awesome food, deathly slow service.
Eat clams. Awesome food, deathly slow service.
0 2021/09/06 18:24:16
0 2021/09/06 18:24:25
0 2021/09/21 09:31:44
0 2021/09/21 09:32:14
0 2021/09/21 09:37:55
0 2021/09/21 09:38:19
Born freee 🎶 As free as the wind blows 🎶
Born freee 🎶 As free as the wind blows 🎶
0 2021/09/21 09:40:23
0 2021/09/21 09:47:43
Scraped it, Supercleaned it, straightened it, sanded it, primed it and painted it.
Scraped it, Supercleaned it, straightened it, sanded it, primed it and painted it.
0 2021/10/17 15:53:46
I used paint I had lying around on the engine side.
I used paint I had lying around on the engine side.
0 2021/10/17 15:53:59
I used my favorite SEM self etching primer and trim black on the visible side.
I used my favorite SEM self etching primer and trim black on the visible side.
0 2021/10/17 15:54:11