YotaTech Forums
Here's my solution to the push vs pull dilemma before I painted it.
Here's my solution to the push vs pull dilemma before I painted it.
0 2021/11/22 08:18:44
install/remove about 30 times, drill/clamp/weld, test fit. only took all day.
install/remove about 30 times, drill/clamp/weld, test fit. only took all day.
0 2021/11/22 08:24:33
with the nylon washers and spacer that I used I had better put some heat shielding here before I put the exhaust together.
with the nylon washers and spacer that I used I had better put some heat shielding here before I put the exhaust together.
0 2021/11/22 08:25:58
0 2021/12/13 14:55:14
Probably won't use the PRNDL from the T100, but maybe later.
Probably won't use the PRNDL from the T100, but maybe later.
0 2021/12/13 15:00:31
Resistance is futile
Resistance is futile
0 2021/12/13 15:02:09
Before, that is in 4x4, so 2wd is WAY forward.
Before, that is in 4x4, so 2wd is WAY forward.
0 2021/12/13 15:07:18
cut a slot
cut a slot
0 2021/12/13 15:08:40
bend it shut, I cut it twice.
bend it shut, I cut it twice.
0 2021/12/13 15:09:26
welded up and welded on the top of the stock shifter
welded up and welded on the top of the stock shifter
0 2021/12/13 15:10:29
plate closed up, that stick is in 2wd in this pic, same angle as 4x4 used to be
plate closed up, that stick is in 2wd in this pic, same angle as 4x4 used to be
0 2021/12/13 15:12:21
0 2021/12/13 15:14:23
Organized mess?
Organized mess?
0 2021/12/16 12:14:25
0 2021/12/16 12:14:56
this should keep my shifter pivot from melting the nylon washers
this should keep my shifter pivot from melting the nylon washers
0 2021/12/16 12:22:45
0 2021/12/16 12:23:32
Rivnut, like a threaded rivot.
Rivnut, like a threaded rivot.
0 2021/12/19 14:55:13
Using my Power steering pulley tool to crush the Rivnuts
Using my Power steering pulley tool to crush the Rivnuts
0 2021/12/19 14:56:45
Instant threaded insert
Instant threaded insert
0 2021/12/19 14:58:12
0 2021/12/19 14:59:03
Far from stock apearance, but it'll work
Far from stock apearance, but it'll work
0 2021/12/19 15:02:05
0 2021/12/19 15:03:47
I covered the hump with a cut up cargo mat, far from stock but it'll do.
I covered the hump with a cut up cargo mat, far from stock but it'll do.
0 2021/12/19 15:07:23
0 2021/12/19 15:08:35
Never going to look better, just had to add a coat of wax.
Never going to look better, just had to add a coat of wax.
0 2022/05/19 18:50:51
swapped out the 3 inch rear leaf springs with 5 inch to fix a little sag.
swapped out the 3 inch rear leaf springs with 5 inch to fix a little sag.
0 2022/05/19 18:51:42
0 2022/05/19 18:52:44
0 2022/11/27 16:56:33
0 2022/11/27 16:57:06
0 2022/11/27 16:59:53
0 2022/11/27 17:03:57
0 2022/11/27 18:45:26
0 2023/05/27 13:52:08
0 2024/01/31 08:50:43
Well, that didn't go as planned
Well, that didn't go as planned
0 2025/11/14 09:04:31
0 2025/11/14 09:26:03