YotaTech Forums
Dead short
Dead short
0 2019/12/02 23:38:15
Open loop
Open loop
0 2019/12/02 23:38:30
0 2020/12/03 19:52:41
0 2020/12/03 19:52:57
0 2020/12/03 19:53:13
0 2021/01/25 05:50:33
0 2021/01/25 05:55:46
0 2021/01/25 05:57:39
0 2021/01/25 06:01:03
0 2021/01/27 20:27:31
0 2021/01/27 20:29:03
0 2021/10/19 08:29:50
0 2021/10/19 08:30:20
0 2021/10/19 08:30:37
0 2021/10/19 08:31:03
0 2021/10/19 08:31:35
0 2021/10/19 08:38:57
0 2021/10/24 13:48:45
3.4 ready to fly
3.4 ready to fly
0 2021/10/24 13:50:25
0 2021/10/24 13:51:06
fits right where the original trans/tcase shifters went.
fits right where the original trans/tcase shifters went.
0 2021/10/24 14:12:55
Looks like some 1/2 inch plate and some gussets should work
Looks like some 1/2 inch plate and some gussets should work
0 2021/10/24 14:14:15
at first I didn't think the front driveshaft would clear the crossmember, but it does.
at first I didn't think the front driveshaft would clear the crossmember, but it does.
0 2021/10/24 14:15:01
front driveshaft mocked up at ride height
front driveshaft mocked up at ride height
0 2021/10/24 14:17:59
0 2021/10/24 14:18:45
Modified alternator bracket to suck it in tighter to the block. before cleanup and powder coat.
Modified alternator bracket to suck it in tighter to the block. before cleanup and powder coat.
0 2021/11/13 17:03:27
the shortest belt I could get on the alternator without further modification
the shortest belt I could get on the alternator without further modification
0 2021/11/13 17:04:39
front axle strapped up to the frame before removing the tires and pulling the 3.0 to get more room for the engine hoist
front axle strapped up to the frame before removing the tires and pulling the 3.0 to get more room for the engine hoist
0 2021/11/13 17:06:12
Make it kneel and you get way better access!!
Make it kneel and you get way better access!!
0 2021/11/13 17:08:08
Here's why I made it bow down! 3.0 gone!
Here's why I made it bow down! 3.0 gone!
0 2021/11/13 17:09:01
0 2021/11/13 17:10:11
0 2021/11/17 13:15:55
tightened the nut a little and welded all in place
tightened the nut a little and welded all in place
0 2021/11/17 13:16:05
my welds still need work, but it'll hold
my welds still need work, but it'll hold
0 2021/11/17 13:16:47
0 2021/11/17 13:17:30
0 2021/11/17 13:17:36
not going anywhere!
not going anywhere!
0 2021/11/17 13:17:40
Just no way I could imagine the original shifter working, so B&M to the rescue. I thought about putting a "teeter totter" pivot assembly towards the rear to change the direction for the cable, but there just isn't enough room to make it work.
Just no way I could imagine the original shifter working, so B&M to the rescue. I thought about putting a "teeter totter" pivot assembly towards the rear to change the direction for the cable, but there just isn't enough room to make it work.
0 2021/11/22 08:18:27
0 2021/11/22 08:18:34
0 2021/11/22 08:18:39