YotaTech Forums
so removed the bracket as i still want to bolt the VSV to the valve cover i need the tab an some of the old bracket
so removed the bracket as i still want to bolt the VSV to the valve cover i need the tab an some of the old bracket
0 2015/08/13 01:23:45
so after a bit of grinding off the excess bits an bending it up i drilled the small hole for a very tiny screw that i found one that fit after being trimmed down to less than 3/8 of an inch
so after a bit of grinding off the excess bits an bending it up i drilled the small hole for a very tiny screw that i found one that fit after being trimmed down to less than 3/8 of an inch
0 2015/08/13 01:24:03
heres the T100 VSV now attached to the tab from the old one
heres the T100 VSV now attached to the tab from the old one
0 2015/08/13 01:24:07
this is the idle adjustment valve if its working when the VSV is activeated it allows more air into the engine bypassing the throtlle plate causing a controled increase in engine rpms which keeps the AC compressor on as it will cycle off at normal idle rpms but not around 1K rpms the white adjuster is how you adjust the AC idle and also works with the power steering if its loading the engine
this is the idle adjustment valve if its working when the VSV is activeated it allows more air into the engine bypassing the throtlle plate causing a controled increase in engine rpms which keeps the AC compressor on as it will cycle off at normal idle rpms but not around 1K rpms the white adjuster is how you adjust the AC idle and also works with the power steering if its loading the engine
0 2015/08/13 01:24:10
an here it is on the engine now i got it with a pigtail of the T100 harness an id recommend it in my case i put a couple male spade terminals on it so they plug into the factory harness plug i could have cut the original harness an put the new in but ehh i taped it all up nice an neat after this so it can be water proof an wont flap around
an here it is on the engine now i got it with a pigtail of the T100 harness an id recommend it in my case i put a couple male spade terminals on it so they plug into the factory harness plug i could have cut the original harness an put the new in but ehh i taped it all up nice an neat after this so it can be water proof an wont flap around
0 2015/08/13 01:24:13
0 2016/01/19 14:42:38
0 2016/01/19 15:54:04
0 2016/01/19 15:54:53
0 2016/01/19 19:04:27
0 2016/01/19 19:05:00
0 2016/01/19 19:05:54
0 2016/01/19 19:06:26
0 2016/01/19 19:13:32
0 2016/01/19 19:14:17
0 2016/01/19 19:15:17
0 2016/01/19 19:16:07
0 2016/01/19 19:18:12
0 2016/01/19 19:18:41
0 2016/01/19 19:19:39
0 2016/01/19 19:20:27
0 2016/01/19 19:21:06
0 2016/01/19 19:21:26
0 2016/01/19 19:21:32
0 2016/01/19 19:23:07
0 2016/01/19 19:23:36
0 2016/01/19 19:24:59
0 2016/01/19 19:25:24
0 2016/01/19 19:26:22
0 2016/01/19 19:26:48
0 2016/01/19 19:27:32
0 2016/01/19 19:28:00
original on the right
original on the right
0 2016/11/22 16:12:39
underside
underside
0 2016/11/22 16:12:42
metal interior plate
metal interior plate
0 2016/11/22 16:12:46
0 2016/11/22 16:12:50
holes marked
holes marked
0 2016/11/22 16:12:53
sodiering iron to melt the holes so they dont fray or rip out
sodiering iron to melt the holes so they dont fray or rip out
0 2016/11/22 16:13:03
reassembling
reassembling
0 2016/11/22 16:13:15
all done
all done
0 2016/11/22 16:13:19
installed in the truck
installed in the truck
0 2016/11/22 16:21:15