Drive shafts
Oct 4, 2005 | 07:53 AM
#1
Thread Starter
Contributing Member
Joined: Jun 2004
Posts: 1,314
Likes: 0
From: Bangkok, Thailand
03 & up 4runner shafts
I bought a bunch of used rear driveshafts from 03 and up 4runners (also fits gx 470's) these are complete flange to flange units with good u-joints, slip yokes and flanges . OEM part number 37110-6A480. most have less than 5000 miles and are like new the worst has about 10k miles on it. I bought them to use in making trail spares (square tube) for myself and my local club. and have quite a few left retail is 540.00 each 
I'm selling for 60.00 shipped anywhere in the lower 48. discounts for multiple units
for 03 and up 4x4 4runners its a bolt in spare!! the flange pattern (4 bolt holes) is standard toyota. they seem to be higher angle than the earler versions. original Toyota equipment
1 shipped 60.00
2 shipped 110.00
local pick up 40..00
I can take pictures but if you don't know what a drive shaft looks like ????
Mike
I'm selling for 60.00 shipped anywhere in the lower 48. discounts for multiple unitsfor 03 and up 4x4 4runners its a bolt in spare!! the flange pattern (4 bolt holes) is standard toyota. they seem to be higher angle than the earler versions. original Toyota equipment
1 shipped 60.00
2 shipped 110.00
local pick up 40..00
I can take pictures but if you don't know what a drive shaft looks like ????
Mike
Last edited by shiftless89; Nov 3, 2005 at 06:36 PM.
Oct 4, 2005 | 09:31 AM
#2
Registered User
Joined: Jan 2003
Posts: 1,958
Likes: 1
From: Smithsburg, Maryland
Are they one piece or the 2 piece with the carrier bearing and double cardine joint? Thanks
Oct 4, 2005 | 10:20 AM
#3
Thread Starter
Contributing Member
Joined: Jun 2004
Posts: 1,314
Likes: 0
From: Bangkok, Thailand
One piece with single U joints on each end, Not the best pic, but quick. I can take more if needed
Last edited by shiftless89; Oct 4, 2005 at 10:41 AM.
Oct 6, 2005 | 10:12 AM
#4
Thread Starter
Contributing Member
Joined: Jun 2004
Posts: 1,314
Likes: 0
From: Bangkok, Thailand
1st grade art project!
NOTE!! THE DRAWING IS INCORECT THE BOLT HOLE CENTERS ARE 6.5CM ON EITHER END
NOTE!! THE DRAWING IS INCORECT THE BOLT HOLE CENTERS ARE 6.5CM ON EITHER END
Last edited by shiftless89; Oct 12, 2005 at 05:17 AM.
Oct 12, 2005 | 05:18 AM
#5
Thread Starter
Contributing Member
Joined: Jun 2004
Posts: 1,314
Likes: 0
From: Bangkok, Thailand
No one needs a spare drive shaft for an 03 or newer 4runner?? at this price you could toss it in the garage and forget about it until you find "that rock"
Nov 3, 2005 | 06:36 PM
#6
Thread Starter
Contributing Member
Joined: Jun 2004
Posts: 1,314
Likes: 0
From: Bangkok, Thailand
bump for updated price
Nov 3, 2005 | 06:38 PM
#7
Registered User
Joined: Nov 2003
Posts: 536
Likes: 0
From: Blowing Rock, NC
I'd be all over it if i had a 4th gen. My 96 is double cardan
Trending Topics
Nov 6, 2005 | 05:45 PM
#8
Thread Starter
Contributing Member
Joined: Jun 2004
Posts: 1,314
Likes: 0
From: Bangkok, Thailand
certain someone pm'd me about one, yet certain someone can't recieve pm's ???
"XXXXy has chosen not to receive private messages or may not be allowed to receive private messages. Therefore you may not send your message to him/her."
"XXXXy has chosen not to receive private messages or may not be allowed to receive private messages. Therefore you may not send your message to him/her."
Last edited by shiftless89; Nov 7, 2005 at 06:24 AM.
Mar 21, 2006 | 08:49 AM
#9
Registered User
Joined: Sep 2005
Posts: 8
Likes: 0
From: Minnesota
Will one of these fit my 1997 4Runner Limited?
Thanks!
Thanks!
Thread
Thread Starter
Forum
Replies
Last Post
FS[GreatLakes]: Toyota collection part out
88sasturbotoy
Axles - Suspensions - Tires - Wheels
3
Jan 30, 2026 01:57 PM
jasonty
Pre 84 Trucks (Build-Up Section)
41
Dec 23, 2018 01:00 PM
FS[PacNorWest]: Rear chromoly axle shafts
A2theK
Axles - Suspensions - Tires - Wheels
5
Jan 10, 2016 10:18 AM
Iceman4193
86-95 Trucks & 4Runners
3
Jul 15, 2015 04:48 PM
