Notices
86-95 Trucks & 4Runners 2nd/3rd gen pickups, and 1st/2nd gen 4Runners with IFS

loping idle, no power, 14 miles on a fresh rebuild?

Thread Tools
 
Search this Thread
 
Old Jan 16, 2011 | 02:32 PM
  #1  
az_eaglescout_pilot's Avatar
Thread Starter
Registered User
iTrader: (1)
 
Joined: Mar 2010
Posts: 239
Likes: 0
From: Tucson, AZ
loping idle, no power, 14 miles on a fresh rebuild?

88 3.0. just got it all installed and buttoned up, drove it for a while, threw code 52, new knock sensor and wire installed now it runs really bad, idle "gallops" i thought it might be timing causing the issues. few questions...the timing is supposed to advance correct? so why when i have the timing light hooked up does the timing not advance? set it at 10* BTDC... the b stands for "behind" TDC or "beyond" TDC? right now with the distributor turned all the way counterclockwise the timing mark is at 15* i have pulled the distributor and moved it one tooth so i could get a little more adjustment but it had no effect, checked the vacuum lines for correct placement twice...could a vacuum line cause the timing to be off?

any help greatly appreciated.

-Jordan
Reply
Old Jan 16, 2011 | 08:30 PM
  #2  
sam333's Avatar
Registered User
 
Joined: Oct 2010
Posts: 270
Likes: 4
BTDC- Before top dead center
Reply
Old Jan 17, 2011 | 08:32 AM
  #3  
az_eaglescout_pilot's Avatar
Thread Starter
Registered User
iTrader: (1)
 
Joined: Mar 2010
Posts: 239
Likes: 0
From: Tucson, AZ
is there a trick to set the timing? in the manual it says to use the "sst" and connect it to terminals te1 and e1...can i do this with out the "sst"?
Reply
Old Jan 17, 2011 | 08:33 AM
  #4  
xxxtreme22r's Avatar
Registered User
 
Joined: Aug 2009
Posts: 13,574
Likes: 72
From: Wilkes-Barre, PA, USA
paperclip.
Reply
Old Jan 17, 2011 | 08:34 AM
  #5  
az_eaglescout_pilot's Avatar
Thread Starter
Registered User
iTrader: (1)
 
Joined: Mar 2010
Posts: 239
Likes: 0
From: Tucson, AZ
so i can just jump the two terminals?
Reply
Old Jan 17, 2011 | 08:39 AM
  #6  
xxxtreme22r's Avatar
Registered User
 
Joined: Aug 2009
Posts: 13,574
Likes: 72
From: Wilkes-Barre, PA, USA
yup. when connected properly your CEL will come on. It might flash can't remember.

this works just as well:


Last edited by xxxtreme22r; Jan 17, 2011 at 08:43 AM.
Reply
Old Jan 17, 2011 | 08:41 AM
  #7  
az_eaglescout_pilot's Avatar
Thread Starter
Registered User
iTrader: (1)
 
Joined: Mar 2010
Posts: 239
Likes: 0
From: Tucson, AZ
ok im gonna try that right now and see what happens...thanks
Reply
Old Jan 17, 2011 | 09:06 AM
  #8  
az_eaglescout_pilot's Avatar
Thread Starter
Registered User
iTrader: (1)
 
Joined: Mar 2010
Posts: 239
Likes: 0
From: Tucson, AZ
alright so i got it to operating temperature, jumped the terminals, and i can get it 10* BTDC but when i drove around the block it backfires a little? timing is still off, if i pull the distributor and move it another tooth will i be ok?
Reply
Old Jan 17, 2011 | 09:33 AM
  #9  
az_eaglescout_pilot's Avatar
Thread Starter
Registered User
iTrader: (1)
 
Joined: Mar 2010
Posts: 239
Likes: 0
From: Tucson, AZ
so this is embarrassing...my number 3 and 5 plug wires were switched...one of those late night mistakes...gahh well she purrs now!
Reply
Old Jan 17, 2011 | 09:49 AM
  #10  
xxxtreme22r's Avatar
Registered User
 
Joined: Aug 2009
Posts: 13,574
Likes: 72
From: Wilkes-Barre, PA, USA
hehe been there done that. Don't feel bad.
Reply
Old Jan 17, 2011 | 09:52 AM
  #11  
az_eaglescout_pilot's Avatar
Thread Starter
Registered User
iTrader: (1)
 
Joined: Mar 2010
Posts: 239
Likes: 0
From: Tucson, AZ
yea i called my dad and told him what it was and he chuckled and said he did that on our boat one time...except he didn't figure it out, the mechanic did for 200 bucks lol now i just need a cat converter that doesn't have something inside of it rattling and i will be golden
Reply
Old Jan 17, 2011 | 09:53 AM
  #12  
xxxtreme22r's Avatar
Registered User
 
Joined: Aug 2009
Posts: 13,574
Likes: 72
From: Wilkes-Barre, PA, USA
Broom handle will fix that converter.
Reply
Old Jan 17, 2011 | 09:59 AM
  #13  
az_eaglescout_pilot's Avatar
Thread Starter
Registered User
iTrader: (1)
 
Joined: Mar 2010
Posts: 239
Likes: 0
From: Tucson, AZ
By whacking it? Hahaha mines welded on both sides...I'm just gonna put a hi-flo on there
Reply
Old Jan 17, 2011 | 10:19 AM
  #14  
xxxtreme22r's Avatar
Registered User
 
Joined: Aug 2009
Posts: 13,574
Likes: 72
From: Wilkes-Barre, PA, USA
hehe nope, by shoving it inside the cat to gut it out.
Reply
Old Jan 17, 2011 | 09:00 PM
  #15  
az_eaglescout_pilot's Avatar
Thread Starter
Registered User
iTrader: (1)
 
Joined: Mar 2010
Posts: 239
Likes: 0
From: Tucson, AZ
well yea i guess theres that too...haha
Reply
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
JF9243176
86-95 Trucks & 4Runners
18
Oct 8, 2017 04:21 AM
yourrealdad
95.5-2004 Tacomas & 96-2002 4Runners
7
Jul 21, 2015 08:53 AM
RyanJ989
Buying & Selling Advice - Feeler/Gauging Interest
0
Jun 21, 2015 06:40 PM
HBoss
Maintenance & Repair Archives
11
Dec 20, 2004 08:45 AM




All times are GMT -8. The time now is 02:31 PM.