YotaTech Forums
Heres a shot of the backside. I think if I were to build an adjustable fence to guide the sheetmeatal in straight, and replaced the handcrank with a large wheel it would make a big difference. Future plans will be to make this thing motorized!
Heres a shot of the backside. I think if I were to build an adjustable fence to guide the sheetmeatal in straight, and replaced the handcrank with a large wheel it would make a big difference. Future plans will be to make this thing motorized!
0 2017/04/24 18:13:03
Its really hard to crank the handle and guide the sheetmetal at the same time. I tried to build a fence to help guide the sheetmetal straight, but it didnt work out. I'll have to redesign it on the next try. It takes some practice, my last bead (the top kne came out pretty straight.
Its really hard to crank the handle and guide the sheetmetal at the same time. I tried to build a fence to help guide the sheetmetal straight, but it didnt work out. I'll have to redesign it on the next try. It takes some practice, my last bead (the top kne came out pretty straight.
0 2017/04/24 18:07:19
0 2017/04/24 18:01:54
0 2017/04/24 18:01:13
0 2017/04/24 18:00:37
0 2017/04/24 17:59:46
0 2017/04/22 01:59:15
0 2017/04/20 13:29:15
0 2017/04/20 13:28:46
0 2017/04/20 13:28:12
second try, i went a little shallower, but I got it centered good this time
second try, i went a little shallower, but I got it centered good this time
0 2017/04/20 13:25:37
0 2017/04/20 13:24:52
çut halfway around, I also forgot to trace the socket with a sharpie so it wasnt centered with the hole
çut halfway around, I also forgot to trace the socket with a sharpie so it wasnt centered with the hole
0 2017/04/20 13:22:52
first try went a little to deep, almost worked as a hole punch
first try went a little to deep, almost worked as a hole punch
0 2017/04/20 13:21:21
The 1" socket fits the inside diameter of the tubing
The 1" socket fits the inside diameter of the tubing
0 2017/04/20 13:19:52
I basically welded a nut to the bottom of a square peice of plate steel. Then I welded a peice of tubing to the other side. Then threaded the bolt up though. I just happened to have the right size flat washers, so I used them as spacers and stacked them up inside the tubing until I got the depth I wanted
I basically welded a nut to the bottom of a square peice of plate steel. Then I welded a peice of tubing to the other side. Then threaded the bolt up though. I just happened to have the right size flat washers, so I used them as spacers and stacked them up inside the tubing until I got the depth I wanted
0 2017/04/20 13:15:43
0 2017/04/20 00:39:10
0 2017/04/19 14:00:37
0 2017/04/19 13:55:33
0 2017/04/19 13:54:28
0 2017/04/19 13:53:10
0 2017/04/19 13:52:43
0 2017/04/19 13:52:18
0 2017/04/19 13:51:44
0 2017/04/18 21:23:37
0 2017/04/18 21:23:11
0 2017/04/18 21:22:42
0 2017/04/18 17:45:31
0 2017/04/18 17:44:53
0 2017/04/18 17:18:49
0 2017/04/18 17:18:05
0 2017/04/18 17:17:05
0 2017/04/18 16:51:49
0 2017/04/18 16:50:26
0 2017/04/18 09:58:01
0 2017/04/18 09:57:41
0 2017/04/13 01:38:01
0 2017/04/13 01:31:21
0 2017/04/13 01:31:02
0 2017/04/13 01:30:46