YotaTech Forums
0 2022/05/24 08:33:31
Mocked up with the DOM cut to size
Mocked up with the DOM cut to size
0 2022/05/24 08:33:29
0 2022/05/24 08:30:46
all together now...
all together now...
0 2022/05/11 15:15:06
Welded up to the cat
Welded up to the cat
0 2022/05/11 15:06:10
Test fitting to see what parts of the original bend(s) I would need to make it work (v-bands are a life safer)
Test fitting to see what parts of the original bend(s) I would need to make it work (v-bands are a life safer)
0 2022/05/11 15:06:08
Welding the step down from 2.5OD-->ID on to the cat
Welding the step down from 2.5OD-->ID on to the cat
0 2022/05/11 15:06:06
My solution, small piece of the stock bend cut out to make the angle work. Took a few tries to get it to the right size on the chop saw but did it little by little
My solution, small piece of the stock bend cut out to make the angle work. Took a few tries to get it to the right size on the chop saw but did it little by little
0 2022/05/11 15:06:03
Here's the front going up to the downpipe off the crossover/collector that has the vband on the end where the A/F goes
Here's the front going up to the downpipe off the crossover/collector that has the vband on the end where the A/F goes
0 2022/05/11 15:06:01
Here it is welded up
Here it is welded up
0 2022/05/11 15:03:28
Here was my solution, I cut a piece out of the original bend. Took a couple tries to get it right and at the correct angle but it was a nice fit as far as I'm concerned.
Here was my solution, I cut a piece out of the original bend. Took a couple tries to get it right and at the correct angle but it was a nice fit as far as I'm concerned.
0 2022/05/11 15:01:57
Test fitting to see what parts of the piece I cutout I will have to use to make it work
Test fitting to see what parts of the piece I cutout I will have to use to make it work
0 2022/05/11 14:49:27
Welding the step down from 2.5ID to OD on to the new CAT
Welding the step down from 2.5ID to OD on to the new CAT
0 2022/05/11 14:47:41
0 2022/05/11 14:25:19
Welded together and attached to the stock exhaust. That is the old single O2 sensor bung blocked off, new one is welded on post the 2 new cats (done before this little project)
Welded together and attached to the stock exhaust. That is the old single O2 sensor bung blocked off, new one is welded on post the 2 new cats (done before this little project)
0 2022/05/11 14:23:51
Mocked up pre-welding, did another test fit and this worked pretty well
Mocked up pre-welding, did another test fit and this worked pretty well
0 2022/05/11 14:23:26
Dry fit and determining what parts of the old bends I needed to cut and use to make it work together
Dry fit and determining what parts of the old bends I needed to cut and use to make it work together
0 2022/05/11 14:22:46
The step down adapter welded to the new CAT, done with stainless .030 wire
The step down adapter welded to the new CAT, done with stainless .030 wire
0 2022/05/11 14:21:34
0 2022/04/21 08:41:34
0 2022/03/18 09:05:59
0 2022/03/18 09:05:33
0 2022/03/18 09:05:30
0 2022/03/18 09:03:44
certiflat 24x48 top
certiflat 24x48 top
0 2022/03/08 08:03:11
leg kit came with heavy duty casters as well
leg kit came with heavy duty casters as well
0 2022/03/08 08:03:08
0 2022/03/08 07:59:30
0 2022/03/08 07:59:27
compressor and lights both on
compressor and lights both on
0 2022/02/28 06:58:34
compressor off, lights on
compressor off, lights on
0 2022/02/28 06:58:32
Compressor on, lights off
Compressor on, lights off
0 2022/02/28 06:58:29
switch mounted to an existing blank
switch mounted to an existing blank
0 2022/02/28 06:58:27
tapped into the clock ignition 12v and illumination 12v
tapped into the clock ignition 12v and illumination 12v
0 2022/02/28 06:58:24
perfect spot for the fuse along the firewall
perfect spot for the fuse along the firewall
0 2022/02/28 06:58:03
0 2022/02/28 06:55:07
everything installed
everything installed
0 2022/02/28 06:55:05
0 2022/02/28 06:55:02
custom paint booth setup
custom paint booth setup
0 2022/02/28 06:54:59
With the catch can mount on it
With the catch can mount on it
0 2022/02/28 06:53:37
0 2022/02/28 06:53:34
this angle ended up being slightly off but i was able to twist it once it was installed on the truck to make it work
this angle ended up being slightly off but i was able to twist it once it was installed on the truck to make it work
0 2022/02/28 06:53:32