YotaTech Forums
0 2022/10/17 07:00:37
We were out in part of the Cameron Peak fire burn scar from the first that ripped through here in 2020
We were out in part of the Cameron Peak fire burn scar from the first that ripped through here in 2020
0 2022/10/17 07:00:31
Same trip, my buddy's beautiful 100 series joined for the fun after we did a full suspension refresh on it
Same trip, my buddy's beautiful 100 series joined for the fun after we did a full suspension refresh on it
0 2022/10/17 07:00:23
welded all together and just waiting for paint
welded all together and just waiting for paint
0 2022/10/07 07:22:07
0 2022/10/07 07:21:56
This is the end plates, the last piece I put on and after the entire project my welds really improved. I'm incredibly proud of the progress just this one (rather large) project gave me in welding.
This is the end plates, the last piece I put on and after the entire project my welds really improved. I'm incredibly proud of the progress just this one (rather large) project gave me in welding.
0 2022/10/07 07:21:46
Both sides tacked in place
Both sides tacked in place
0 2022/10/07 07:21:42
fitting a bit more snuggly in there, really like how it's fitting now and the bar routing
fitting a bit more snuggly in there, really like how it's fitting now and the bar routing
0 2022/10/07 07:20:53
initial notch
initial notch
0 2022/10/07 07:20:48
passenger side headlight bar cut down
passenger side headlight bar cut down
0 2022/10/07 07:20:43
much better clearance around the hood
much better clearance around the hood
0 2022/10/07 07:20:37
0 2022/10/07 07:20:32
marking my lines to make the cuts into the headlight tubes, this is where I really had no clue what I was doing
marking my lines to make the cuts into the headlight tubes, this is where I really had no clue what I was doing
0 2022/10/07 07:20:27
How it sits now with the length added back to the center
How it sits now with the length added back to the center
0 2022/10/07 07:20:21
I'll take it!
I'll take it!
0 2022/10/07 07:19:13
re-leveling after getting all the pieces back on
re-leveling after getting all the pieces back on
0 2022/10/07 07:19:06
Welding said pieces back on, I put a bevel into the pieces I was reattaching to give myself somewhere to weld
Welding said pieces back on, I put a bevel into the pieces I was reattaching to give myself somewhere to weld
0 2022/10/07 07:19:01
Here you can see how the hood will hit with the bars this low, I had to go back through and weld the pieces I cut off back on eventually
Here you can see how the hood will hit with the bars this low, I had to go back through and weld the pieces I cut off back on eventually
0 2022/10/07 07:18:11
how the bars sat with the center bar cut a little too low, it ended up interfering with the hood
how the bars sat with the center bar cut a little too low, it ended up interfering with the hood
0 2022/10/07 07:17:29
0 2022/10/07 07:17:24
Leveling the center bar after my initial cut...which had to get redone later
Leveling the center bar after my initial cut...which had to get redone later
0 2022/10/07 07:17:18
fully welded up and upside down on my welding table
fully welded up and upside down on my welding table
0 2022/09/21 07:03:14
just some photos of my beginner welds
just some photos of my beginner welds
0 2022/09/21 07:01:58
just some photos of my beginner welds
just some photos of my beginner welds
0 2022/09/21 07:01:53
starting to get the backside fully welded
starting to get the backside fully welded
0 2022/09/21 07:01:49
both sides tacked in and on the truck
both sides tacked in and on the truck
0 2022/09/21 07:01:44
Passenger side fully tacked in, did have some fitment issues here with the plates not lining up perfectly but that's definitely caused by my lack of experience putting something like this together
Passenger side fully tacked in, did have some fitment issues here with the plates not lining up perfectly but that's definitely caused by my lack of experience putting something like this together
0 2022/09/21 06:59:36
First front plate tacked in place, this has the hole for the LED turn signal
First front plate tacked in place, this has the hole for the LED turn signal
0 2022/09/21 06:59:31
how it looks from the front, super happy with this
how it looks from the front, super happy with this
0 2022/09/21 06:59:26
Using my big 10 ton jack to hold the top wing up while I get it tacked in place
Using my big 10 ton jack to hold the top wing up while I get it tacked in place
0 2022/09/21 06:59:21
0 2022/09/21 06:57:21
complete plating tacked on the passenger side
complete plating tacked on the passenger side
0 2022/09/21 06:57:17
front plate where the turn signal mounts tacked on
front plate where the turn signal mounts tacked on
0 2022/09/21 06:57:13
how it looks from the front
how it looks from the front
0 2022/09/21 06:57:06
0 2022/09/21 06:57:01
How I supported the passenger side getting the wing tacked on
How I supported the passenger side getting the wing tacked on
0 2022/09/21 06:56:56
front view, squares are for lights which I have some Baja designs squadron sport lights to go into even though they technically aren't the correct mounting type I'm hoping to make them fit.
front view, squares are for lights which I have some Baja designs squadron sport lights to go into even though they technically aren't the correct mounting type I'm hoping to make them fit.
0 2022/09/09 13:08:37
Back of it all tacked into place with the front winch plate in too where a fairlead will mount to
Back of it all tacked into place with the front winch plate in too where a fairlead will mount to
0 2022/09/09 13:08:32
Sitting on the truck with the side pieces (previous photo with the recovery point in them) and the winch plate tacked in
Sitting on the truck with the side pieces (previous photo with the recovery point in them) and the winch plate tacked in
0 2022/09/09 13:08:27
Simple clamp setup but it made life super easy when lining these two plates up to weld. The hole is one of of two front recovery points that is two pieces of 3/16 plate to reinforce the recovery point locations
Simple clamp setup but it made life super easy when lining these two plates up to weld. The hole is one of of two front recovery points that is two pieces of 3/16 plate to reinforce the recovery point locations
0 2022/09/09 13:08:22