YotaTech Forums
The injectors should measure 1.5 - 3 ohms.
The injectors should measure 1.5 - 3 ohms.
0 2017/05/06 21:14:57
0 2017/05/06 21:13:31
0 2017/05/06 21:11:19
0 2017/04/27 04:56:58
Ox is almost right in the middle, bottom row
Ox is almost right in the middle, bottom row
0 2017/04/26 19:17:00
0 2017/02/12 09:26:24
0 2017/01/13 10:18:49
0 2017/01/03 18:38:04
0 2017/01/02 17:37:25
The butyl rubber windshield seal doesn't look perfect, but I'm betting my cab leak's gone. I might try to find a strip of rubber to press over top. It'll look more finished and won't attract as much dirt.
The butyl rubber windshield seal doesn't look perfect, but I'm betting my cab leak's gone. I might try to find a strip of rubber to press over top. It'll look more finished and won't attract as much dirt.
0 2016/11/29 08:43:13
Driver's side. Note the rock chip holes are gone.
Driver's side. Note the rock chip holes are gone.
0 2016/11/29 08:42:55
Passenger side wasn't terrible to begin with so it cleaned up better.
Passenger side wasn't terrible to begin with so it cleaned up better.
0 2016/11/29 08:42:43
Windshield chanel. The butyl tape isn't in there yet and it already looks very waterproof.
Windshield chanel. The butyl tape isn't in there yet and it already looks very waterproof.
0 2016/11/27 17:03:39
Also primed around the fuel door panel. I think I'm gonna fill the holes for the rock chip guards. Mine are in bad shape and I run mudflaps now. I also think it looks better without them.
Also primed around the fuel door panel. I think I'm gonna fill the holes for the rock chip guards. Mine are in bad shape and I run mudflaps now. I also think it looks better without them.
0 2016/11/27 16:59:35
Inside at front of wheel well.
Inside at front of wheel well.
0 2016/11/27 16:57:51
Inside seam at back of wheel well.
Inside seam at back of wheel well.
0 2016/11/27 16:57:04
Driver's side. This is after 2 coats of Rust Seal.
Driver's side. This is after 2 coats of Rust Seal.
0 2016/11/27 16:53:24
I trimmed the glue to make a V shaped chanel. Brushed on naval jelly, wire brushed, then liquid phosphoric acid. Tomorrow I'll sand, paint with Rust Seal, then press a 1/4" rope of butyl rubber into the channel. Eventually I'll get a new windshield, but this is a cheap fix for now that should stop the leak till I get around to the replacement. I used butyl rubber a few years ago on the rear-most side windows and I'm convinced they'll never leak again.
I trimmed the glue to make a V shaped chanel. Brushed on naval jelly, wire brushed, then liquid phosphoric acid. Tomorrow I'll sand, paint with Rust Seal, then press a 1/4" rope of butyl rubber into the channel. Eventually I'll get a new windshield, but this is a cheap fix for now that should stop the leak till I get around to the replacement. I used butyl rubber a few years ago on the rear-most side windows and I'm convinced they'll never leak again.
0 2016/11/26 16:45:33
Had a small leak into the cab so I pulled the chrome trim to investigate. I'm never putting it back on. It had trapped leaves, pine needles and dirt that was damp after being in the garage for days. This is after scraping the paint off.
Had a small leak into the cab so I pulled the chrome trim to investigate. I'm never putting it back on. It had trapped leaves, pine needles and dirt that was damp after being in the garage for days. This is after scraping the paint off.
0 2016/11/26 16:45:22
I always thought the rearview and visors seemed springy. Turns out the support had detached. JB weld to the rescue.
I always thought the rearview and visors seemed springy. Turns out the support had detached. JB weld to the rescue.
0 2016/11/26 16:36:30
Didn't take a before pic, but this is straight as an arrow compared to what it was.
Didn't take a before pic, but this is straight as an arrow compared to what it was.
0 2016/11/26 16:35:49
Rear bumper 's been twisted bad and dented up ever since I've had the truck. Today seemed like the right day to pull it and bash some the damage out. It'll get paint tomorrow.
Rear bumper 's been twisted bad and dented up ever since I've had the truck. Today seemed like the right day to pull it and bash some the damage out. It'll get paint tomorrow.
0 2016/11/26 16:35:05
0 2016/11/26 16:21:15
0 2016/11/26 16:20:31
Wire-wheeled, acid-treated and repainted only one year ago!
Wire-wheeled, acid-treated and repainted only one year ago!
0 2016/09/24 13:29:22
This is just enough untreated rust to eff up the exterior.
This is just enough untreated rust to eff up the exterior.
0 2016/09/24 13:27:49
Took hours to get them to mate together! Had to remove the lower half of the engine mounts to make it happen, so maybe try that first and save yourself a big headache.
Took hours to get them to mate together! Had to remove the lower half of the engine mounts to make it happen, so maybe try that first and save yourself a big headache.
0 2016/09/13 15:11:04
0 2016/09/13 15:08:21
NPW water pump, supposedly better quality than U.S.-made aisin pumps.
NPW water pump, supposedly better quality than U.S.-made aisin pumps.
0 2016/09/13 15:02:21
Engnbldr stock head and cam, osk timing kit w/ plastic guides, original bolts all cleaned by hand, which really su*ked.
Engnbldr stock head and cam, osk timing kit w/ plastic guides, original bolts all cleaned by hand, which really su*ked.
0 2016/09/13 14:49:38
The original paint cleaned up pretty well with simple green and the occasional shot of goof off. Waxed it to keep it looking good.
The original paint cleaned up pretty well with simple green and the occasional shot of goof off. Waxed it to keep it looking good.
0 2016/09/13 14:46:35
I pulled the bellhousing which made cleanup a breeze and used a dry paper gasket to seal up the input seal cover. Permatex #2 on the bolts. No leaks!
I pulled the bellhousing which made cleanup a breeze and used a dry paper gasket to seal up the input seal cover. Permatex #2 on the bolts. No leaks!
0 2016/09/13 14:45:34
0 2016/09/04 16:34:10
0 2016/09/04 16:30:42
0 2016/09/04 16:27:33
0 2016/09/04 16:24:49
0 2016/09/04 16:24:18
0 2016/09/04 16:23:32
0 2016/09/04 16:23:04
0 2016/09/04 16:21:32