YotaTech Forums
0 2026/02/02 16:27:24
0 2026/02/02 16:27:20
0 2026/02/02 16:23:11
0 2026/02/01 17:21:38
0 2026/02/01 17:14:59
0 2026/02/01 17:11:51
0 2026/02/01 17:11:12
Spindle bushing greased.
Spindle bushing greased.
0 2026/02/01 17:04:53
Axle, nothing to explain. Lone your flat spots on the birfield with top and bottom and work your way into the diff. With almost all gaskets i touch they always get a light layer of anti seize. It'll keep them from rusting and make lofe much eaisier for the next person to take it apart.
Axle, nothing to explain. Lone your flat spots on the birfield with top and bottom and work your way into the diff. With almost all gaskets i touch they always get a light layer of anti seize. It'll keep them from rusting and make lofe much eaisier for the next person to take it apart.
0 2026/02/01 17:04:50
Before axle goes in i put a healthy amount of grease between the ball and knuckle. More can be added later through threaded plug on top of knuckle.
Before axle goes in i put a healthy amount of grease between the ball and knuckle. More can be added later through threaded plug on top of knuckle.
0 2026/02/01 17:04:47
0 2026/02/01 16:56:19
0 2026/02/01 16:55:45
0 2026/02/01 16:53:03
0 2026/02/01 16:40:07
Before knuckle goes on inner ring, rubber seal and felt must go over the ball first. Once knuckle is set then they will be bolted to knuckle. 10mm bolts torqued to 8Lbs.
Before knuckle goes on inner ring, rubber seal and felt must go over the ball first. Once knuckle is set then they will be bolted to knuckle. 10mm bolts torqued to 8Lbs.
0 2026/02/01 16:40:03
0 2026/02/01 16:35:00
0 2026/02/01 16:34:58
0 2026/02/01 16:34:55
0 2026/02/01 16:34:52
0 2026/02/01 16:30:43
0 2026/02/01 16:30:33
0 2026/02/01 16:29:30
0 2026/02/01 16:28:43
0 2026/02/01 16:26:27
0 2026/02/01 16:26:24
0 2026/02/01 16:24:05
0 2026/01/30 18:04:39
Alot of people always use permatex for this gasket. Which is fine, ive done pleny myself. But this truck looks pretty good and the gaskets are only like $5 a piece. Using the gasket gives it a better fit and finish imo. Thin layer of anti sieze on the housing, factory paper gasket, then another thin layer of anti seize.
Alot of people always use permatex for this gasket. Which is fine, ive done pleny myself. But this truck looks pretty good and the gaskets are only like $5 a piece. Using the gasket gives it a better fit and finish imo. Thin layer of anti sieze on the housing, factory paper gasket, then another thin layer of anti seize.
0 2026/01/30 18:04:36
Same, cleaned up hasket surface.
Same, cleaned up hasket surface.
0 2026/01/30 18:04:33
Low grit schotch pad to clean up the gasket surface. Stiffed with rags to keep any trash out.
Low grit schotch pad to clean up the gasket surface. Stiffed with rags to keep any trash out.
0 2026/01/30 18:04:30
Painted
Painted
0 2026/01/30 18:00:32
Once hanging i did final prep, same as before.
Once hanging i did final prep, same as before.
0 2026/01/30 18:00:30
Inside of truss and top of axle where truss goess was pre painted as you saw. Truss was dry fitted, wire wheel along the edge to get and paint off and welded.
Inside of truss and top of axle where truss goess was pre painted as you saw. Truss was dry fitted, wire wheel along the edge to get and paint off and welded.
0 2026/01/30 18:00:27
0 2026/01/16 13:42:47
0 2026/01/15 13:42:59
Both knuckles and hubs painted.
Both knuckles and hubs painted.
0 2026/01/15 13:42:53
0 2026/01/15 13:42:47
Wire wheel on both knuckles and hubs. Quick spray down with brake clean. Skim over with sand paper/scotch pad. Spray with brake clean then a good wipe down with acetone.
Wire wheel on both knuckles and hubs. Quick spray down with brake clean. Skim over with sand paper/scotch pad. Spray with brake clean then a good wipe down with acetone.
0 2026/01/15 13:42:40
0 2026/01/15 13:42:33
0 2026/01/15 13:42:26