YotaTech Forums
First forklift test. notice shocks disconnected. got 24 inch Limited by linkage. Old Springs.
First forklift test. notice shocks disconnected. got 24 inch Limited by linkage. Old Springs.
0 2020/09/08 20:24:23
Regeared diff to 5.71 gears. Decided may as well close my eyes and bite the bullit.. got an eaton ELocker
Regeared diff to 5.71 gears. Decided may as well close my eyes and bite the bullit.. got an eaton ELocker
0 2020/09/08 20:24:37
0 2020/09/08 20:24:53
Finally done with construction. Got my rear suspension mods started on Monday. Actually went well for the first piece of the puzzle. I will just drop a pic of the top shock mount tacked for test fit. :)
Finally done with construction. Got my rear suspension mods started on Monday. Actually went well for the first piece of the puzzle. I will just drop a pic of the top shock mount tacked for test fit. :)
0 2021/01/19 22:48:38
Final fitment
Final fitment
0 2021/01/25 22:53:53
0 2021/01/25 22:54:18
0 2021/01/25 22:54:41
0 2021/01/25 22:55:10
Full compression. Thats 3 inches further up than ome shock from previous setup. OME shocks were great though!
Full compression. Thats 3 inches further up than ome shock from previous setup. OME shocks were great though!
0 2021/01/25 22:55:33
0 2021/01/25 22:55:55
0 2021/01/25 22:56:16
Decided to use a hiem joint i had laying around to build a longer and adjustable panhard bar. Needed it to be a little longer
Decided to use a hiem joint i had laying around to build a longer and adjustable panhard bar. Needed it to be a little longer
0 2021/01/25 22:56:40
Built a custom rear suspension setup using stock mounting points.
Built a custom rear suspension setup using stock mounting points.
0 2021/01/31 14:07:45
Took it for a test drive today to check clearances and enjoy the fruits of my labor. I Am very happy with the outcome. Articulation and behavior are significantly improved for offroad use. You can see the build in my build thread if you are interested.
Took it for a test drive today to check clearances and enjoy the fruits of my labor. I Am very happy with the outcome. Articulation and behavior are significantly improved for offroad use. You can see the build in my build thread if you are interested.
0 2021/01/31 14:08:03
Final weld
Final weld
0 2021/03/28 09:24:42
0 2021/03/28 09:24:57
0 2021/03/28 09:25:07
Tack weld strengthening ribs
Tack weld strengthening ribs
0 2021/03/28 09:25:23
admire, test fitment
admire, test fitment
0 2021/03/28 09:25:37
Not fun
Not fun
0 2021/03/28 09:25:52
Final weld cross member
Final weld cross member
0 2021/03/28 09:26:08
Test. Cut exhaust
Test. Cut exhaust
0 2021/03/28 09:26:25
Measure cut bend
Measure cut bend
0 2021/03/28 09:26:38
get the stuff $70
get the stuff $70
0 2021/03/28 09:26:55
not fun
not fun
0 2021/03/28 09:27:09
Good enough for now (new CAT in a few months, will have shop install new clean setup
Good enough for now (new CAT in a few months, will have shop install new clean setup
0 2021/03/28 09:27:25
Problem solved :)
Problem solved :)
0 2021/03/29 09:15:22
New fox steering stabilizer. One end was too wide
New fox steering stabilizer. One end was too wide
0 2021/03/29 09:15:36
It's done. Painting will come later, after a couple of shakedown trips.
It's done. Painting will come later, after a couple of shakedown trips.
0 2021/03/29 09:15:50
I will be testing the strength in the weakest part with a jack. Should lift the car a bit before starting to bend. It is very strong, I am confident :)
I will be testing the strength in the weakest part with a jack. Should lift the car a bit before starting to bend. It is very strong, I am confident :)
0 2021/03/29 09:16:03
0 2021/04/09 23:12:36
0 2021/04/09 23:17:43
0 2021/04/09 23:17:59
0 2021/04/09 23:18:10
0 2021/04/09 23:18:23
0 2021/04/09 23:18:34
0 2021/04/09 23:18:48
0 2021/04/13 22:52:36
0 2021/04/13 22:53:47
0 2021/04/13 22:54:52