YotaTech Forums
After a few beads I got the hang of the new welder.
After a few beads I got the hang of the new welder.
0 2020/02/16 21:00:24
Had to drill out the taped 1/2" hole to 5/8. This bolt is actually under lots of load in this design. Grade 8 - 5/8" bolt installed.
Had to drill out the taped 1/2" hole to 5/8. This bolt is actually under lots of load in this design. Grade 8 - 5/8" bolt installed.
0 2020/02/16 21:00:32
All welded up and a very glossy black paint job completed. I added two gussets to the top bar. You can kind of see in this pic.
All welded up and a very glossy black paint job completed. I added two gussets to the top bar. You can kind of see in this pic.
0 2020/02/16 21:00:38
Checked clearanced.
Checked clearanced.
0 2020/02/16 21:00:46
more checking.
more checking.
0 2020/02/16 21:00:54
And I think it looks great!
And I think it looks great!
0 2020/02/16 21:01:03
also. wtf? 5 year old mount :(
also. wtf? 5 year old mount :(
0 2020/02/21 19:27:58
0 2020/02/21 19:28:14
0 2020/02/21 19:28:25
0 2020/02/21 19:28:34
0 2020/02/21 19:29:56
0 2020/02/21 19:30:04
0 2020/02/21 19:30:12
0 2020/02/21 19:30:19
0 2020/02/21 19:30:27
0 2020/02/23 19:10:08
0 2020/02/23 19:11:04
0 2020/02/23 19:12:21
0 2020/02/23 19:13:16
0 2020/02/23 19:14:33
0 2020/02/23 19:18:39
0 2020/02/23 19:19:17
Then this was delivered, found a good deal!
Then this was delivered, found a good deal!
0 2020/04/19 22:53:17
Step two, finish mockup
Step two, finish mockup
0 2020/04/19 22:53:26
About 1000 posts ago on this thread I talked about doing this. Making my own low profile, but more importantly 1 inch drivetrain lift. Step 1, make a mockup.
About 1000 posts ago on this thread I talked about doing this. Making my own low profile, but more importantly 1 inch drivetrain lift. Step 1, make a mockup.
0 2020/04/19 22:53:35
First, finished that holly mess. Young kids screwed up the alignment though and it isn't good, but I am confident once I get it done (Covid 19 is in the way) It will be good
First, finished that holly mess. Young kids screwed up the alignment though and it isn't good, but I am confident once I get it done (Covid 19 is in the way) It will be good
0 2020/04/19 22:53:46
Some parts are delivered.
Some parts are delivered.
0 2020/04/19 22:57:16
May as well get to that cargo drawer you had been planning forever
May as well get to that cargo drawer you had been planning forever
0 2020/04/19 22:57:21
Step 3, run out of steel and can't get anymore because nothing is open!
Step 3, run out of steel and can't get anymore because nothing is open!
0 2020/04/19 22:57:28
But, needed a place to install. No space in hood.
But, needed a place to install. No space in hood.
0 2020/04/19 22:57:37
Then, finally found a good deal on this!!
Then, finally found a good deal on this!!
0 2020/04/19 22:57:45
more stuff is delivered
more stuff is delivered
0 2020/04/19 23:01:08
Making a harness (threw several additional wires in there for ease future growth.
Making a harness (threw several additional wires in there for ease future growth.
0 2020/04/19 23:01:14
Install dual voltmeter, Install ARB rocker switch in stock rear defrost switch location. Run out of toggle switches, temporarily install dinky one... (that switch is to manually open and close relay circuit connecting and disconnecting dual batteries, I need DPDT.
Install dual voltmeter, Install ARB rocker switch in stock rear defrost switch location. Run out of toggle switches, temporarily install dinky one... (that switch is to manually open and close relay circuit connecting and disconnecting dual batteries, I need DPDT.
0 2020/04/19 23:01:23
Take off dash parts. Remove rear window defrost button. Be confused at the too many wires going into the defrost switch, do research to make sure you are not disabling other circuits. 90% sure you aren't? Good enough. Take 5 hrs to run new wires from back to front, through dash. Go do yoga, come back and do more wiring.
Take off dash parts. Remove rear window defrost button. Be confused at the too many wires going into the defrost switch, do research to make sure you are not disabling other circuits. 90% sure you aren't? Good enough. Take 5 hrs to run new wires from back to front, through dash. Go do yoga, come back and do more wiring.
0 2020/04/19 23:01:33
Clean up wires. Order oddyssey battery less than 7 inches high.
Clean up wires. Order oddyssey battery less than 7 inches high.
0 2020/04/19 23:01:42
FIgure out that complicated ARB compressor harness. Wiring diagram is only for use with two solenoids... hmmm. Test, success!
FIgure out that complicated ARB compressor harness. Wiring diagram is only for use with two solenoids... hmmm. Test, success!
0 2020/04/19 23:01:52
Buy some felt. Install some felt. Run out of plywood!! :? Find old inverter, it's not heavy! Install for fun!
Buy some felt. Install some felt. Run out of plywood!! :? Find old inverter, it's not heavy! Install for fun!
0 2020/04/19 23:02:03
0 2020/04/25 23:48:35
0 2020/04/25 23:49:09