YotaTech Forums
Share Your Pictures with Our Community. Upload Now
0 2026/01/30 18:52:37
0 2026/01/30 18:23:01
0 2026/01/30 18:04:39
Alot of people always use permatex for this gasket. Which is fine, ive done pleny myself. But this truck looks pretty good and the gaskets are only like $5 a piece. Using the gasket gives it a better fit and finish imo. Thin layer of anti sieze on the housing, factory paper gasket, then another thin layer of anti seize.
Alot of people always use permatex for this gasket. Which is fine, ive done pleny myself. But this truck looks pretty good and the gaskets are only like $5 a piece. Using the gasket gives it a better fit and finish imo. Thin layer of anti sieze on the housing, factory paper gasket, then another thin layer of anti seize.
0 2026/01/30 18:04:36
Same, cleaned up hasket surface.
Same, cleaned up hasket surface.
0 2026/01/30 18:04:33
Low grit schotch pad to clean up the gasket surface. Stiffed with rags to keep any trash out.
Low grit schotch pad to clean up the gasket surface. Stiffed with rags to keep any trash out.
0 2026/01/30 18:04:30
Painted
Painted
0 2026/01/30 18:00:32
Once hanging i did final prep, same as before.
Once hanging i did final prep, same as before.
0 2026/01/30 18:00:30
Inside of truss and top of axle where truss goess was pre painted as you saw. Truss was dry fitted, wire wheel along the edge to get and paint off and welded.
Inside of truss and top of axle where truss goess was pre painted as you saw. Truss was dry fitted, wire wheel along the edge to get and paint off and welded.
0 2026/01/30 18:00:27
0 2026/01/28 17:21:29
0 2026/01/28 10:02:34
0 2026/01/28 10:02:31
Advertisement
Installed.
Installed.
0 2026/01/27 18:56:59
0 2026/01/27 18:56:56
3D view
3D view
0 2026/01/27 18:56:53
End view
End view
0 2026/01/27 18:56:51
Top view with the back of clutch fork on the left side. The clips have a curly q on one end which fits into a depression in the back side of the fork while the other end wraps around the ear on the clutch collar holding that in place. The clutch bearing (on the right hand side in this pic) is pressed onto the collar with the round face of the bearing facing the engine.
Top view with the back of clutch fork on the left side. The clips have a curly q on one end which fits into a depression in the back side of the fork while the other end wraps around the ear on the clutch collar holding that in place. The clutch bearing (on the right hand side in this pic) is pressed onto the collar with the round face of the bearing facing the engine.
0 2026/01/27 18:56:48
Front view of assembly
Front view of assembly
0 2026/01/27 18:56:44
0 2026/01/27 17:45:47
All bolted up.
All bolted up.
0 2026/01/27 17:45:44
0 2026/01/27 17:45:41
The lift maxed out just clearing the front end.
The lift maxed out just clearing the front end.
0 2026/01/27 17:45:38
New flywheel, clutch and pressure plate installed.
New flywheel, clutch and pressure plate installed.
0 2026/01/27 17:45:34
0 2026/01/26 16:53:00
Cable extension installed.
Cable extension installed.
0 2026/01/25 17:27:06
Simpson nailer on left after being cut in half. Finished cable extension on the right.
Simpson nailer on left after being cut in half. Finished cable extension on the right.
0 2026/01/25 17:27:02
Glamour photo of rear axle with completed brake lines.
Glamour photo of rear axle with completed brake lines.
0 2026/01/25 17:26:58
0 2026/01/23 18:25:13
Support beam on the opposite side along with a 6 x 8 support post. Secondary beams are 4 x 6 for with 2 x 6 purlins every 30”. All hardware and fasteners are from Simpson’s architectural product line.
Support beam on the opposite side along with a 6 x 8 support post. Secondary beams are 4 x 6 for with 2 x 6 purlins every 30”. All hardware and fasteners are from Simpson’s architectural product line.
0 2026/01/23 18:14:29
This is one of the main support beams for the extra roof along with a support post. They’re both 6 x 8 Doug Firs. Had to take a hedge trimmer to the side just to clear out enough creeper to work.
This is one of the main support beams for the extra roof along with a support post. They’re both 6 x 8 Doug Firs. Had to take a hedge trimmer to the side just to clear out enough creeper to work.
0 2026/01/23 18:14:25
0 2026/01/21 12:05:29
How she looks now
How she looks now
0 2026/01/21 12:04:54
Advertisement