YotaTech Forums
Share Your Pictures with Our Community. Upload Now
0 2026/03/03 11:28:38
0 2026/03/03 11:28:34
0 2026/03/03 11:28:30
Hey Disco the carpet was oversized about 4” lengthwise and width wise. It went in fairly well with the only problem area being the wrinkle about 6” in front of the shifters. I think the console is going to cover that.
Hey Disco the carpet was oversized about 4” lengthwise and width wise. It went in fairly well with the only problem area being the wrinkle about 6” in front of the shifters. I think the console is going to cover that.
0 2026/03/02 16:59:57
And a Stubby antennae!
And a Stubby antennae!
0 2026/03/01 17:22:09
0 2026/02/28 17:06:24
0 2026/02/28 17:06:20
0 2026/02/27 22:04:40
0 2026/02/27 18:50:08
0 2026/02/27 18:50:05
0 2026/02/26 21:39:02
0 2026/02/26 21:38:58
Advertisement
0 2026/02/26 21:38:56
Here’s the Kovax system. The sanding blocks are very small and the paper is precut to fit each block. There is a small curved block (not shown) and a Tolecard which has the size and flexibility of a playing card so it works best on most of the body panel curves.
Here’s the Kovax system. The sanding blocks are very small and the paper is precut to fit each block. There is a small curved block (not shown) and a Tolecard which has the size and flexibility of a playing card so it works best on most of the body panel curves.
0 2026/02/26 18:33:54
Got started with the polishing on the right front fender.
Got started with the polishing on the right front fender.
0 2026/02/26 18:32:21
0 2026/02/26 09:28:14
0 2026/02/26 05:01:21
0 2026/02/26 05:01:18
0 2026/02/25 16:05:52
0 2026/02/25 16:05:47
0 2026/02/25 16:05:43
0 2026/02/25 16:05:38
Silver Metallic hockey stick design
Silver Metallic hockey stick design
0 2026/02/23 19:30:39
0 2026/02/23 17:08:53
0 2026/02/23 17:08:45
This is how the shock wants to sit using the factory bottom shock mounts on the front axle. Trail gear said to keep the shock bushings happy, not to push them too far one way or the other. But too keep the shock within the 12:00-1:00 ramge in terms of angle and It'll be good.
This is how the shock wants to sit using the factory bottom shock mounts on the front axle. Trail gear said to keep the shock bushings happy, not to push them too far one way or the other. But too keep the shock within the 12:00-1:00 ramge in terms of angle and It'll be good.
0 2026/02/23 17:08:39
Shock hoops tacked up. Paper says to install with 40% of shock length exposed. I used rebar tie wire to set my length before i set it in position. However with the length set to what they recommend the shock hoop would not land completely on the frame. I pulled it back out and extended 1/2". This allowed both ends of the hoop to be fully seated against frame. The extra 1/2" will be counterd at ride height once the springs settle and still yeild me close to 40% exposed.
Shock hoops tacked up. Paper says to install with 40% of shock length exposed. I used rebar tie wire to set my length before i set it in position. However with the length set to what they recommend the shock hoop would not land completely on the frame. I pulled it back out and extended 1/2". This allowed both ends of the hoop to be fully seated against frame. The extra 1/2" will be counterd at ride height once the springs settle and still yeild me close to 40% exposed.
0 2026/02/23 17:08:30
0 2026/02/23 16:59:03
Set of old factory steelies from outback with stock size tire. Did end up having to bring truck a little high to roll these on to it.
Set of old factory steelies from outback with stock size tire. Did end up having to bring truck a little high to roll these on to it.
0 2026/02/23 16:58:55
But finally axle is under the truck for now.
But finally axle is under the truck for now.
0 2026/02/23 16:58:45
This photo feels like a misrepresentation with the time involved to get the bushings,shackles,leaf springs,axle all bolted together. Had the axle on a small cart, fortunately the truck was already high enough to roll it under the springs. Getting the axle high enough to catch the ubolts, and get the leaf spring pins lined up definitely takes a little bit.
This photo feels like a misrepresentation with the time involved to get the bushings,shackles,leaf springs,axle all bolted together. Had the axle on a small cart, fortunately the truck was already high enough to roll it under the springs. Getting the axle high enough to catch the ubolts, and get the leaf spring pins lined up definitely takes a little bit.
0 2026/02/23 16:58:34
Bushings going in. Grease inside tube and on bushing. As before used the large vise grips to push them in.
Bushings going in. Grease inside tube and on bushing. As before used the large vise grips to push them in.
0 2026/02/23 16:58:23
Advertisement