toyotafiberglass - Mojave tribute build
Nov 7, 2016 | 05:31 PM
#242
Thread Starter
Joined: Jan 2006
Posts: 6,382
Likes: 301
From: BC Canada
little more today ..
got the new matched shift boots done .. steering wheel , console lid , and now shift boots ....
.
got the new matched shift boots done .. steering wheel , console lid , and now shift boots ....
.
Last edited by slacker; Mar 21, 2018 at 05:42 PM.
Nov 11, 2016 | 04:02 PM
#246
Thread Starter
Joined: Jan 2006
Posts: 6,382
Likes: 301
From: BC Canada
With the added air volume , and now the larger injectors , I needed a larger fuel supply , so I added a new walbro 255LPH pump today .. original walbro , not a cheep china knock off !!!!
out with the OE original pump ,
and in with the new hi volume pump
.
out with the OE original pump ,
and in with the new hi volume pump
.
Last edited by slacker; Nov 11, 2016 at 04:04 PM.
Nov 14, 2016 | 04:14 PM
#247
Thread Starter
Joined: Jan 2006
Posts: 6,382
Likes: 301
From: BC Canada
so with the cab off .. I decided to do another coat of POR15 .. so I sanded the surface , and brushed on another layer .
all dried , I got the engine in place and clutch installed
and tranny fully installed .
.
all dried , I got the engine in place and clutch installed
and tranny fully installed .
.
Last edited by slacker; Mar 21, 2018 at 05:51 PM.
Nov 21, 2016 | 04:35 PM
#251
Thread Starter
Joined: Jan 2006
Posts: 6,382
Likes: 301
From: BC Canada
getting real close now 
got my headers back from ceramic coat .. and I just had to see what there gonna look like
happy happy happy
.
got my headers back from ceramic coat .. and I just had to see what there gonna look like
happy happy happy
.
Last edited by slacker; Mar 21, 2018 at 05:55 PM.
Nov 25, 2016 | 07:31 PM
#255
Thread Starter
Joined: Jan 2006
Posts: 6,382
Likes: 301
From: BC Canada
well here we go ........
Cab back from paint .. and final assembly begins ..
some firewall heat protection .. .. sorry . didn't get any final pics , but trust me , the firewall is covered
Cab back from paint .. and final assembly begins ..
some firewall heat protection .. .. sorry . didn't get any final pics , but trust me , the firewall is covered
Last edited by slacker; Mar 21, 2018 at 05:58 PM.
Dec 4, 2016 | 03:48 PM
#258
Thread Starter
Joined: Jan 2006
Posts: 6,382
Likes: 301
From: BC Canada
so , taking this way to far .. time to clean and rebuild the heating system
heater box already out , I started dismantling and cleaning .
part of this section you can not split as it is spot welded .. I decided to "split " it anyway , so I can replace the disintegrated foam
.
heater box already out , I started dismantling and cleaning .
part of this section you can not split as it is spot welded .. I decided to "split " it anyway , so I can replace the disintegrated foam
.
Last edited by slacker; Mar 21, 2018 at 06:07 PM.
Dec 4, 2016 | 03:51 PM
#259
Thread Starter
Joined: Jan 2006
Posts: 6,382
Likes: 301
From: BC Canada
main box today .. pulled it all apart as well , cleaned re-foamed , and back together
re rounded the core tube ends , and added a new heater core as well
and what is a rebuilt heater box , with out a rebuilt motor , so I tore into it as well
good thing I did .. failure was imminent .. brushes warn to the nub .
all done .. and back together . Tested , and works awesome !
little splash of black on the exterior , and I'm ready to install the whole shootin' match
.
re rounded the core tube ends , and added a new heater core as well
and what is a rebuilt heater box , with out a rebuilt motor , so I tore into it as well
good thing I did .. failure was imminent .. brushes warn to the nub .
all done .. and back together . Tested , and works awesome !
little splash of black on the exterior , and I'm ready to install the whole shootin' match
.
Last edited by slacker; Mar 21, 2018 at 06:13 PM.
