**SOLD**For Sale/ Trade, '99 Chevy 5.3L LM7, $700obo in Mount Carmel, PA
07-10-2012, 02:07 PM
#1
Registered User
Thread Starter
**SOLD**For Sale/ Trade, '99 Chevy 5.3L LM7, $700obo in Mount Carmel, PA
1999 Vortec 5300 5.3L LM7
Cast block/ alum heads
Throttle Cable motor
This was bought to jump under the hood of my 92 Land Cruiser but that project went to the back burner, and eventually my original hype fizzled out.
To the best of my knowledge this is a 55K motor out of a rear hit 1500 Silverado. Motor is free, spins over as it should. Motor has all accessories excluding A/C bracket & pump, Fan (clutch is there, Rock Auto = $36.99 new fan or go E-fan), nor motors mounts. Other than that the motor is complete. I have the engine harness with extra computer plugs (the blue & red), the computer, extra throttle body, both the square & rounded "Vortec" cover, MAF, flexplate, some misc bolts. This motor does have both stock exhaust manifolds included. There are 4 snapped exhaust man. studs on the drivers side, just never got around to getting them out after I lost interest in the project. The oil pan had a 1/2" crack by the oil filter, I did the best I could to Tig weld the crack (I'm a welder by trade) and have faith in it, but no gaurentee with this 13 year old oil impregnated cast alum.
I've tried to take alot of pics and video of the whole thing, if you need any specifics, I can get them. Please check this motor out and make sure this is all you believe it to be before you take it home. This motor is AS IS, if I had a use for it, I'd throw this in some Yota junk tomorrow.
Motor is located in Mount Carmel, PA 17851 (20min north on 81 from Rausch Creek Offroad Park)
$700 obo, more than willing to trade / trade + cash either way for but not limited to the following:
Geared and/or locked 8" thirds
HP 8"
FJ80/FZJ80 Front axle, radius arms, coils, steering box
FJ80/FZJ80 parts in general
Dual case and/or 4.7 case
COMPLETE 22RET turbo setup
Complete 5VZ
R151F
36 or 37"tires
2 axle Car Trailer
Any other good yota stuff
Pics
Snapped studs
Welded pan....inside and out
Extra stuff & harness
VIDEO!!! Motor has good compression turning over, and cylinder bores look @#$% nice and visable cross hatching still!
Cast block/ alum heads
Throttle Cable motor
This was bought to jump under the hood of my 92 Land Cruiser but that project went to the back burner, and eventually my original hype fizzled out.
To the best of my knowledge this is a 55K motor out of a rear hit 1500 Silverado. Motor is free, spins over as it should. Motor has all accessories excluding A/C bracket & pump, Fan (clutch is there, Rock Auto = $36.99 new fan or go E-fan), nor motors mounts. Other than that the motor is complete. I have the engine harness with extra computer plugs (the blue & red), the computer, extra throttle body, both the square & rounded "Vortec" cover, MAF, flexplate, some misc bolts. This motor does have both stock exhaust manifolds included. There are 4 snapped exhaust man. studs on the drivers side, just never got around to getting them out after I lost interest in the project. The oil pan had a 1/2" crack by the oil filter, I did the best I could to Tig weld the crack (I'm a welder by trade) and have faith in it, but no gaurentee with this 13 year old oil impregnated cast alum.
I've tried to take alot of pics and video of the whole thing, if you need any specifics, I can get them. Please check this motor out and make sure this is all you believe it to be before you take it home. This motor is AS IS, if I had a use for it, I'd throw this in some Yota junk tomorrow.
Motor is located in Mount Carmel, PA 17851 (20min north on 81 from Rausch Creek Offroad Park)
$700 obo, more than willing to trade / trade + cash either way for but not limited to the following:
Geared and/or locked 8" thirds
HP 8"
FJ80/FZJ80 Front axle, radius arms, coils, steering box
FJ80/FZJ80 parts in general
Dual case and/or 4.7 case
COMPLETE 22RET turbo setup
Complete 5VZ
R151F
36 or 37"tires
2 axle Car Trailer
Any other good yota stuff
Pics
Snapped studs
Welded pan....inside and out
Extra stuff & harness
VIDEO!!! Motor has good compression turning over, and cylinder bores look @#$% nice and visable cross hatching still!
Thread
Thread Starter
Forum
Replies
Last Post
mordell
95.5-2004 Tacomas & 96-2002 4Runners
4
09-12-2015 10:13 AM
