BLKNBLU

iTrader: (1)

No longer available

I am considering moving my tire and wheel setup.

Falken Wildpeak AT 265/70/17 on black steel 17x8 wheels. Lugnuts included. No centercaps. Per the math the tires are 31.60 tall and 10.43 wide. I don't know about backspacing on the rims, but have no interference issues whatsoever on a 2nd gen suspension with ball joint spacers.

I am happy with this setup and won't mind using it down to the last shred of rubber if there is no interest. It's just that I have a set of 15 inch Toyota alloy wheels in the garage that I would like to put into service and de-clutter my workspace. In fact, I will likely get these same tires again in the new size.

We would have to work it out as I would need the cash from the sale to offset some of the new tire cost, but those are details we could certainly work out.

$600

Pics:




I also have a Bridgestone spare in the same size on an FJ steel wheel that appears to have never touched the ground I could throw in as a spare for an extra $75

glideraz

the wheels have a 0 off set which means the hub part of the wheel is right in the middle of the wheel if that helps you out mike

Zachwild101

Looking for wheels and tires in the Tucson area, looking for 305-70-16 or 33s or 35s for 16 inch rims
Also looking for manuel lockers for the front of my rig

I drive a 91 runner

Duckie

I know its not the right place, but ill throw it up to you local guys. Looking to see how much my ARB bumper is worth. It's in pretty good condition, pictures can be seen in my profile. Off of my 1st gen IFS 4runner.

joeynational

iTrader: (1)

Anyone have a SR5 grey steering wheel 89-95? I'm in the East Valley

92-95 4runner front bumper,valance and brackets would be cool too!

angrybob

I have a IFS front diff (86-95 manual hubs if 2nd Gen) with Yukon 4.88 gears and a Lockright. About 2 years old and less than 500 miles of 4wd. Works perfectly. Selling because I just installed an ARB. $350

Custom fab'd rear tire carrier that fits into 2" tow hitch or bumper with receiver. Has lisence plate relocation kit and hi-lift mount. Folds down by removing a pin to open tailgate. Can also do light towing with it installed as it has its own receiver. Very well made. $300

jrhende

How much for bumper?

Phessor

I just paid $600.00 for one out of Texas.
Wished you would have posted this earlier.

Phessor

bmxjedi

Looking for an intake tube out of a 22re, maybe someone has one laying around? If not I'll just do tubing

joeynational

iTrader: (1)

I actually have some polished aluminum tubing I'm not going to use that I would be willing to sell, let me know and I'll get some pics up

Duckie

Hey man I apologize a ton. I was off the forum for a long time when I was working on the timing chain. Truck sat for 10 months... I just saw your pm. Again man I apologize.

I'm thinking to ask around 600 for mine. In my profile picture you can see the only mar on the bumper, next to the pass. side turn signal.

mmacguy

Trying to get a few bare minimum items to get her rolling again. She's a 1980 4x4 Pickup son and I are working on. I'm rebuilding the shifter seat, but found the odd bolt that connects the shifter base to the L43 shaft is stripped and falling out! Camelback Toyota can't find one. They have ordered in 2 incorrect parts so far....I give up on them. I see a number 33521F on a diagram that appears correct, so I know someone knows these and has these somewhere! Second, need to move up to some LT315/75R16's I have from my bad 31x10.5 15's and need 4 rims. Plain, simple, even painted black, I don't care! From what I've read, my 3" lift should be enough to make them work out. If you know differently, please let me know! Please email if you have them and they work. Otherwise, I will stay with the 15's. I'm near 35th ave and Bethany Home.

After that, the real work, bushings, fuel lines, tanks connect, electic clean up and bed goes on. Then the big list: Seats, (early 4 runner I think)
Cage, tube doors, bikini kit, Ac compressor. I'm exhausted thinking about it.

I've searched the threads several times with no luck on an idea I had -- has anyone ever tried a FJ40 fold down windshield, in conjunction with a cage and tube doors on a 1st gen pickup? Am I nuts to think it might be cool? Thoughts? Thanks, I sure am glad I found this group!

Duckie

Officially listing my ARB front bumper. $600 obo, or Ill make a deal for $1000 with M8000 winch. It is currently still on my 4 runner. Phx, Yuma, Flag peeps, ill consider meeting halfway if interested.

az_eaglescout_pilot

iTrader: (1)

WTB 1st gen SR5 4runner interior door panels! PM if you have any in good condition collecting dust...

Replicant

Also looking for a driveshaft from a 90-95 MANUAL 4 runner. Did an auto to manual swap and need the 5spd driveshaft. Somebody got one cheap in the East Valley?

87 Deathtrap

SOLD

I've got a set of 16x7 factory tacoma wheels if you're interested. How does $60 for the set sound? All 4 are straight and in good shape with just some wear from being rolled around. At 48th St & Southern.

BLKNBLU

iTrader: (1)

SOLD

I have some stock Toyota alloys I want to move. 15x7 split 3 spoke type. IIRC they are all in not perfect but very nice shape. I'll dig them out tomorrow and get better shots of them and verify their condition. Total of 5 for $100 to you guys. If they are still around on Monday night when I have finished my work w/e I will throw them on CL for $150. Here is a pic of the top one.

bmxjedi

I have a 2WD transmission from a 3.0 motor out of a 90 toyota pickup that I'm not using. It was in a Lucas oil prerunner back In the day, was going to use it in mine but went with a 22 re instead. I can text pics if interested. Looking to get $100, spread the word!

Phessor

I need to get rid of these soon or off to the scrap yard they go.

79-85
1980 4X4 grill and headlight doors = $50.00 OBO
front 3" lift springs
front stock springs
steering components
rear axles with brake components = $75.00 OBO
rear axle housing = Make offer $$$

85-88
frame
cab
doors
fenders
hood
bed
split bench seat
upper & lower a arms
spindles
half shafts
rotors
calipers
torsion bars
rear housing
rear axles
dash pieces
top shift transfer case SPF to 87 Deathtrap
front center section with 4.10 gears
rear drive line
front drive line
Make offer on above items $$$

89-95
upper & lower a arms
spindles
half shafts
rotors
calipers
torsion bars
rear axle housing
4 cyl flexplate
automatic 4X4 shifter and short console
Make offer on above items $$$
front axle assembly with 4.56 gears = $150.00 OBO
rear axles with brake components = $75.00


four 15" X 10" white spoke rims Make offer $$$













I am in the White Mountains but I make it down to Phoenix a couple times a month, make me an offer on any parts you need!!!
If you need a part shipped it's on your dime.

Phessor

Replicant

Looking for a alternator plug from a 3.4 harness, apparently I lost mine. Also, still looking for a driveshaft from a 5spd 90-95 4runner. PM!