YotaTech Forums
The trucks been sitting in my drive way for over a year waiting on the previous owner to figure out what he wanted to do with it.
The trucks been sitting in my drive way for over a year waiting on the previous owner to figure out what he wanted to do with it.
0 2015/05/30 19:56:58
interior is dirty but in way better shape than the 82 I fixed up.
interior is dirty but in way better shape than the 82 I fixed up.
0 2015/05/30 19:55:20
speading a lil mud
speading a lil mud
0 2012/11/15 15:24:22
planning on taking out 15" but decided I did not want to bob the shell 3"
planning on taking out 15" but decided I did not want to bob the shell 3"
0 2012/10/29 14:48:23
first cut with a jig saw
first cut with a jig saw
0 2012/10/29 14:46:45
sawsall cut!...look at that line
sawsall cut!...look at that line
0 2012/10/29 14:43:52
point of well....
point of well....
0 2012/10/29 14:43:52
had to notch the bed support to clear the crossmember that held the spare tire
had to notch the bed support to clear the crossmember that held the spare tire
0 2012/10/29 14:43:52
side of bed after final cut
side of bed after final cut
0 2012/10/29 14:41:16
inside of bed after final cut
inside of bed after final cut
0 2012/10/29 14:41:16
Mag shot
Mag shot
0 2012/10/29 14:41:16
section removed
section removed
0 2012/10/29 14:39:00
new bed mount
new bed mount
0 2012/10/29 14:39:00
added bed mounts
added bed mounts
0 2012/10/29 14:39:00
the worst side
the worst side
0 2012/10/29 14:35:27
still have som rust repair to do
still have som rust repair to do
0 2012/10/29 14:35:27
welded on inside of bed
welded on inside of bed
0 2012/10/29 14:35:27
first time shell sat on bobbed bed
first time shell sat on bobbed bed
0 2012/10/29 14:32:03
bobbed with shell it fits it fits
bobbed with shell it fits it fits
0 2012/10/29 14:32:03
after bob before body work
after bob before body work
0 2012/10/29 14:32:03
resoldered
resoldered
0 2012/10/15 07:08:31
where it should go
where it should go
0 2012/10/15 07:08:31
Loose wire
Loose wire
0 2012/10/15 07:08:31
tank cleaned painted and ready to install
tank cleaned painted and ready to install
0 2012/10/15 07:04:21
found some frame rot!!!
found some frame rot!!!
0 2012/10/15 07:04:21
fuel pickup really clean
fuel pickup really clean
0 2012/10/15 07:02:05
Inside of tank is really clean!!!!
Inside of tank is really clean!!!!
0 2012/10/15 07:02:05
Tank with all the dirt knocked off along with some old paint...
Tank with all the dirt knocked off along with some old paint...
0 2012/10/15 07:02:05
tab was bent at a 90 degree angle now its bent far enough back to let he gauge drop to E. Float does not hit bottom of tank. I tried to bend the rod but it did not make a differnce
tab was bent at a 90 degree angle now its bent far enough back to let he gauge drop to E. Float does not hit bottom of tank. I tried to bend the rod but it did not make a differnce
0 2012/10/15 06:53:15
tab that was not letting the float go all the way down.
tab that was not letting the float go all the way down.
0 2012/10/15 06:53:15
fuel level sending unit
fuel level sending unit
0 2012/10/15 06:53:15
top limb too much!
top limb too much!
0 2012/07/24 06:34:34
custom painted my bow fishing bow, 1987 Bear Black Bear compound bow
custom painted my bow fishing bow, 1987 Bear Black Bear compound bow
0 2012/07/24 06:33:16
lower limb
lower limb
0 2012/07/24 06:33:16
left side of riser
left side of riser
0 2012/07/24 06:33:16
Toyota Pulsar[1]
Toyota Pulsar[1]
0 2012/08/22 12:08:24
it will even open up side down...lol just showing both doors flipped up
it will even open up side down...lol just showing both doors flipped up
0 2012/06/30 20:28:54
both doors flipped up for good access to the bed
both doors flipped up for good access to the bed
0 2012/06/30 20:28:54
all fits good pealed off the old spray on bed liner that was put on it..
all fits good pealed off the old spray on bed liner that was put on it..
0 2012/06/30 20:23:27
storm door opens good drags on the bottom just a little I have to raise the bottom hinge about 1/8 of an inch
storm door opens good drags on the bottom just a little I have to raise the bottom hinge about 1/8 of an inch
0 2012/06/30 20:23:27