YotaTech Forums
0 2020/01/04 17:14:28
0 2020/01/04 17:14:22
0 2020/01/04 17:14:16
0 2020/01/03 18:40:37
0 2019/12/25 06:15:11
0 2019/12/25 06:13:31
0 2019/12/25 06:13:28
0 2019/12/25 06:13:25
0 2019/11/13 14:07:04
0 2019/11/13 14:06:48
0 2019/11/13 14:06:40
0 2019/11/13 14:06:34
0 2019/11/13 14:05:47
0 2019/11/04 13:16:19
0 2019/11/04 13:16:14
Full underview with 4 new stops.
Full underview with 4 new stops.
0 2019/10/26 09:38:59
Driver side view
Driver side view
0 2019/10/26 09:38:55
Strap wrench and deep well 14mm
Strap wrench and deep well 14mm
0 2019/10/26 09:38:51
Part number for you
Part number for you
0 2019/10/26 09:38:45
0 2019/10/20 08:35:25
0 2019/10/20 08:35:22
splashes beware, im guarded.
splashes beware, im guarded.
0 2019/10/06 10:29:41
in case your wondering, the little fin cut up front is because the prototype truck had tires too big and rubbed the guards. may replace later but doesnt bother me now.
in case your wondering, the little fin cut up front is because the prototype truck had tires too big and rubbed the guards. may replace later but doesnt bother me now.
0 2019/10/06 10:29:33
0 2019/10/06 10:29:26
0 2019/10/06 10:29:21
all better. torque spec is 130 foot pounds.
all better. torque spec is 130 foot pounds.
0 2019/10/06 10:18:20
apply the pitman arm puller, put some tension on it, and give it a few wacks with your hammer to break it free
apply the pitman arm puller, put some tension on it, and give it a few wacks with your hammer to break it free
0 2019/10/06 10:18:13
use a brass hammer and impact the flat spot on the linkage to jar it loose.
use a brass hammer and impact the flat spot on the linkage to jar it loose.
0 2019/10/06 10:18:06
save these...
save these...
0 2019/10/06 10:18:00
my socket set is a 3/4 inch drive which makes removal pretty easy
my socket set is a 3/4 inch drive which makes removal pretty easy
0 2019/10/06 10:17:53
your 32 mm socket required for removal and installatin of the nut, which youll need to reuse.
your 32 mm socket required for removal and installatin of the nut, which youll need to reuse.
0 2019/10/06 10:17:47
this is the oem part number
this is the oem part number
0 2019/10/06 10:17:41
after installing the airbag, check to ensure your control stick works. bam, you have cruise control.
after installing the airbag, check to ensure your control stick works. bam, you have cruise control.
0 2019/09/21 05:51:20
this is the bezel PN
this is the bezel PN
0 2019/09/21 05:51:15
install the new bezel
install the new bezel
0 2019/09/21 05:51:07
these are the screws you will need, there are two
these are the screws you will need, there are two
0 2019/09/21 05:51:01
install the control stick like this
install the control stick like this
0 2019/09/21 05:50:54
this is a PN for the new ground wire. simply remove the existing wire, and replace it with the new one which has an extra wire for the control stick.
this is a PN for the new ground wire. simply remove the existing wire, and replace it with the new one which has an extra wire for the control stick.
0 2019/09/21 05:50:48
remove the two wires from the back of the airbag by pulling out of the yellow tabs, and pulling straight back on the connectors.
remove the two wires from the back of the airbag by pulling out of the yellow tabs, and pulling straight back on the connectors.
0 2019/09/21 05:50:42
loosen the two torque head screws on either side of the wheel, this will allow removal of the airbag.
loosen the two torque head screws on either side of the wheel, this will allow removal of the airbag.
0 2019/09/21 05:50:36