YotaTech Forums
Dash tweeter. Yes, I drilled a hole for this.
Dash tweeter. Yes, I drilled a hole for this.
0 2016/08/03 20:10:31
Boston 4" jammed into the 4T location. Foam bucket behind it.
Boston 4" jammed into the 4T location. Foam bucket behind it.
0 2016/08/03 20:13:30
Boston Cross Over
Boston Cross Over
0 2016/08/03 20:13:31
Dash tweeter. Yes, I drilled a hole for it.
Dash tweeter. Yes, I drilled a hole for it.
0 2016/08/03 20:13:31
NAPA for the win High side cheap adapter fits Lo side fits, but you will never be able to connect the manifold I put right angle adapters on both sides Steel ones From NAPA
NAPA for the win High side cheap adapter fits Lo side fits, but you will never be able to connect the manifold I put right angle adapters on both sides Steel ones From NAPA
0 2016/08/06 05:33:00
This was after vac via the blower motor hole
This was after vac via the blower motor hole
0 2016/08/06 05:33:08
Ick
Ick
0 2016/08/06 05:33:14
Washed with dish soap and a rag I took it out of the box! Did not get water in the tube Blew it all off with compressed air
Washed with dish soap and a rag I took it out of the box! Did not get water in the tube Blew it all off with compressed air
0 2016/08/06 05:33:24
Still more poop Blower box
Still more poop Blower box
0 2016/08/06 05:33:32
Static pressure Yeah, I didn't know to burp it Gonna have a shop pull it, and I'll re charge it after I add a new drier
Static pressure Yeah, I didn't know to burp it Gonna have a shop pull it, and I'll re charge it after I add a new drier
0 2016/08/06 05:33:39
Running pressures are ok Blows 45 After 2 hours of driving at 95 deg, blows 55 :( I'll get the air out and I think it will be fine
Running pressures are ok Blows 45 After 2 hours of driving at 95 deg, blows 55 :( I'll get the air out and I think it will be fine
0 2016/08/06 05:33:48
See how tight the low side would be after attaching a straight adapter
See how tight the low side would be after attaching a straight adapter
0 2016/08/06 06:11:24
0 2016/08/07 12:09:56
0 2016/08/07 12:09:59
gap between the rad and the cross member I usually stuff a 2" block of foam in here (i.e. AC weather strip) - It had that weather strip when new
gap between the rad and the cross member I usually stuff a 2" block of foam in here (i.e. AC weather strip) - It had that weather strip when new
0 2016/08/08 19:43:26
0 2016/08/19 06:40:01
0 2016/08/19 06:40:02
crawling its way through the mess of wires and hoses that go to the dash board gauges
crawling its way through the mess of wires and hoses that go to the dash board gauges
0 2016/08/19 06:59:11
0 2016/08/22 14:23:57
2 2016/08/23 17:14:05
Inner fender well rust
Inner fender well rust
0 2016/08/23 19:37:07
Page 1 of 4
Page 1 of 4
0 2016/08/28 14:55:34
Page 2 of 4
Page 2 of 4
0 2016/08/28 14:55:35
Page 4 of 4
Page 4 of 4
0 2016/08/28 14:55:36
Page 3 of 4
Page 3 of 4
0 2016/08/28 14:55:37
0 2016/08/29 08:51:34
Ivan Stewart's 4Runner Pre Runner (its a 2WD Ranger frame and a Ford V8 with a Gen1 4Runner body)
Ivan Stewart's 4Runner Pre Runner (its a 2WD Ranger frame and a Ford V8 with a Gen1 4Runner body)
0 2016/08/30 11:14:50
0 2016/08/30 16:37:08
0 2016/08/30 16:37:09
Drivers side - repaired
Drivers side - repaired
0 2016/09/05 18:52:02
Drivers side - pre repair
Drivers side - pre repair
0 2016/09/05 18:52:04
Tapping the hole - drivers side
Tapping the hole - drivers side
0 2016/09/05 18:52:04
Passenger side - repaired
Passenger side - repaired
0 2016/09/05 18:52:05
how it sits on top of the blower
how it sits on top of the blower
0 2016/09/11 19:31:43
Found a spare blower box!
Found a spare blower box!
0 2016/09/11 19:31:44
the upper layer can get bent to fit around the cowl box. Its all "wired" together. It should be mouse proof,
the upper layer can get bent to fit around the cowl box. Its all "wired" together. It should be mouse proof,
0 2016/09/11 19:31:45
0 2016/09/11 19:34:25
0 2016/09/11 19:34:26
0 2016/09/11 19:34:27
box located on top of lower cowl hole
box located on top of lower cowl hole
0 2016/09/11 19:35:10