YotaTech Forums
Share Your Pictures with Our Community. Upload Now
0 2026/02/07 16:14:18
0 2026/02/07 16:13:24
Foreground hose can be disconnected for more working room. Background house is to the pipe we're replacing
Foreground hose can be disconnected for more working room. Background house is to the pipe we're replacing
0 2026/02/06 20:32:15
Pressure test gauge -- be careful not to overpressure from the schrader valve
Pressure test gauge -- be careful not to overpressure from the schrader valve
0 2026/02/06 20:32:14
0 2026/02/06 16:25:40
Wheel studs got a anti seize around the whole thing, grease would work too. This mainly for a lubrication as they set into place. Got them started with light hits with hammer and punch.
Wheel studs got a anti seize around the whole thing, grease would work too. This mainly for a lubrication as they set into place. Got them started with light hits with hammer and punch.
0 2026/02/06 16:25:33
The rotor to hub face on both side i put a thin layer of anti seize mainly as a rust prevention. The two bolts that hold the rotor before the wheel studs go in. A dab of anti seize then torqued to 34Lbs, book says 29 -39Lbs.
The rotor to hub face on both side i put a thin layer of anti seize mainly as a rust prevention. The two bolts that hold the rotor before the wheel studs go in. A dab of anti seize then torqued to 34Lbs, book says 29 -39Lbs.
0 2026/02/06 16:25:26
Time for oil seals from hub to spindle. Grease on the hub and outsode edge of oil seal. Can get it started with some light taps around the edge. Paper towel to keep dirt out from the block of wood used to set them in place.
Time for oil seals from hub to spindle. Grease on the hub and outsode edge of oil seal. Can get it started with some light taps around the edge. Paper towel to keep dirt out from the block of wood used to set them in place.
0 2026/02/06 16:22:20
0 2026/02/06 16:22:16
From the rear axle
From the rear axle
0 2026/02/05 17:09:05
Walkers aftermarket equivalent of the OEM muffler bolted right up to the two bolt hanger.
Walkers aftermarket equivalent of the OEM muffler bolted right up to the two bolt hanger.
0 2026/02/05 17:09:01
The last two pieces in this photo still need clamps
The last two pieces in this photo still need clamps
0 2026/02/05 17:08:58
Advertisement
One final test fit of the filler.
One final test fit of the filler.
0 2026/02/05 17:08:55
From the front
From the front
0 2026/02/05 17:08:52
No cat. Tried Walker Mega Clamps on this to save on the welds and they are nice. Stout and clean.
No cat. Tried Walker Mega Clamps on this to save on the welds and they are nice. Stout and clean.
0 2026/02/05 16:59:16
Walkers aftermarket equivalent of the OEM muffler bolted right up to the stock hanger.
Walkers aftermarket equivalent of the OEM muffler bolted right up to the stock hanger.
0 2026/02/05 16:59:12
The last two joints in the 2” piping need clamps. It’s a very simple exhaust with all straight piping starting at the 4 into 2 section and extending all the way to the 45 elbow and turndown p
The last two joints in the 2” piping need clamps. It’s a very simple exhaust with all straight piping starting at the 4 into 2 section and extending all the way to the 45 elbow and turndown p
0 2026/02/05 16:59:08
0 2026/02/05 16:59:04
View from the front
View from the front
0 2026/02/05 16:58:59
0 2026/02/05 16:50:07
0 2026/02/05 16:50:02
0 2026/02/05 15:41:16
0 2026/02/05 15:38:32
0 2026/02/05 11:29:33
0 2026/02/05 11:28:40
0 2026/02/05 11:27:56
0 2026/02/05 11:26:40
0 2026/02/05 11:26:02
0 2026/02/05 11:20:13
0 2026/02/05 11:19:04
0 2026/02/05 11:17:59
0 2026/02/05 11:16:31
Advertisement