Notices
86-95 Trucks & 4Runners 2nd/3rd gen pickups, and 1st/2nd gen 4Runners with IFS

Identifying Performance Cam

Thread Tools
 
Search this Thread
 
Old Dec 8, 2014 | 02:37 PM
  #1  
92 Yoda's Avatar
Thread Starter
Registered User
 
Joined: Dec 2014
Posts: 39
Likes: 0
From: AHHTAWAHH
Identifying Performance Cam

Howdy folks,

I'm buying a performance head with an after market cam locally that was in a burnt truck. The guy I'm buying it from bought the whole motor at auction and therefore isn't sure the exact cam that's in it but he says it was listed as being freshly rebuilt, bored over with head work done along with the cam. He's selling the block guaranteed to be good but told me he wasn't sure if the head was alright so I'm getting the whole head with cam for cheap.

First off would the head be damaged by the fire? Even if the head was damaged would the cam have been damaged?

I'm only counting on getting a cam out of this deal so I'm not super worried if the heads damaged. But provided it's alright how would I be able to identify the cam? Do most after market cams have engravings of would it be down to measuring and matching lobes?

Any advice is appreciated!
Reply
Old Dec 8, 2014 | 10:21 PM
  #2  
92 Yoda's Avatar
Thread Starter
Registered User
 
Joined: Dec 2014
Posts: 39
Likes: 0
From: AHHTAWAHH
Nobodies done a Cam in there 22re?
Reply
Old Dec 8, 2014 | 11:30 PM
  #3  
Robert m's Avatar
Registered User
15 Year Member
Liked
Loved
Community Favorite
iTrader: (2)
 
Joined: May 2006
Posts: 1,974
Likes: 143
From: Apple Valley, CA
Lots of people have done cams but I'd say 99% of them are cams that are ordered new so its already known what it is before install. I'd call LCE and engbldr and ask them. Its been a few years since my cam was installed but I dont remember any markings on it.
Reply
Old Dec 9, 2014 | 12:34 PM
  #4  
wyoming9's Avatar
Registered User
iTrader: (1)
 
Joined: Apr 2009
Posts: 13,381
Likes: 100
From: I live in New Tripoli Pa out in the woods
Red face

Did you see the truck the engine was pulled from??

There are fires Then their are Fires!!

Depending just how hot things got the whole engine could be toast if it was hot and hit with cold water .

Think major over heating but lots worse.

If it was driven home after the fire you should be ok.

The only way to tell the cam is to measure it. compare it with the specs of what it is supposed to be.

Building any kind of power in these engines is so very expensive.
Reply
Old Dec 9, 2014 | 01:10 PM
  #5  
92 Yoda's Avatar
Thread Starter
Registered User
 
Joined: Dec 2014
Posts: 39
Likes: 0
From: AHHTAWAHH
I'm going to see him tomorrow or the next day and Ill ask him. He said the block was fine so I assume it wasn't that serious. I'm just looking to get the cam out of it so even if the heads a little rough its not big deal.

I don't want to make huge power just for the price I might as well throw a cam in my truck if I can.
Reply
Old Dec 9, 2014 | 02:02 PM
  #6  
Rowdydudeman's Avatar
Registered User
 
Joined: May 2013
Posts: 400
Likes: 0
From: San Antonio, Tx.
there should be a part number on it somewhere, usually on the firewall side of the shake stick.
Reply
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
LittleUgly
86-95 Trucks & 4Runners (Build-Up Section)
15
Jan 2, 2020 01:30 PM
Iceman4193
86-95 Trucks & 4Runners
22
Oct 16, 2015 10:50 AM
kbpickens
Newbie Tech Section
5
Oct 2, 2015 03:37 PM
JookUpVandetti
86-95 Trucks & 4Runners
10
Sep 30, 2015 08:58 AM
oldblue
86-95 Trucks & 4Runners
0
Sep 28, 2015 04:07 PM




All times are GMT -8. The time now is 01:22 AM.