Who's using Yakima Q towers on a 3rd gen?
#1
Registered User
Thread Starter
Join Date: Jul 2004
Location: Jupiter, FL
Posts: 1,921
Likes: 0
Received 0 Likes
on
0 Posts
Who's using Yakima Q towers on a 3rd gen?
Ok so I'm looking for users of Q towers with Q-62 clips. I'm fitting a Hannibal roof rack to the truck and will need some additional support up front. I have 3 sets of control towers spread over my factory rack. Lets see some pictures if you have them.
Aaron
Aaron
#4
Registered User
Thread Starter
Join Date: Jul 2004
Location: Jupiter, FL
Posts: 1,921
Likes: 0
Received 0 Likes
on
0 Posts
Well I wanted a picture of what it looks like on, measurements from outer edge to underside of bar, top of bar. Center height from center roof line to bottom, top of bar.
Thanks
Aaron
Thanks
Aaron
#6
Registered User
Join Date: Jun 2005
Location: Rocky Top, Tennessee
Posts: 501
Likes: 0
Received 0 Likes
on
0 Posts
lets see what i got...
i have the 66" bars i think (longest ones) with the towers
sorry theses are the best pictures i have right now, if i get back early enough tonight from practice i could take some up send em your way if you need em.
i have the 66" bars i think (longest ones) with the towers
sorry theses are the best pictures i have right now, if i get back early enough tonight from practice i could take some up send em your way if you need em.
#7
Registered User
Join Date: Feb 2007
Location: Las Cruces, NM
Posts: 481
Likes: 0
Received 0 Likes
on
0 Posts
My set up...
0214 control towers
0408 round bars 48''
0221 Landing pads
7204 SKS locks
7047 38" fairing
BasketCase
Last edited by Vermejo; 11-28-2007 at 11:32 AM.
Trending Topics
#8
Registered User
Thread Starter
Join Date: Jul 2004
Location: Jupiter, FL
Posts: 1,921
Likes: 0
Received 0 Likes
on
0 Posts
Thank You
Aaron
#9
Registered User
Join Date: Jun 2005
Location: Rocky Top, Tennessee
Posts: 501
Likes: 0
Received 0 Likes
on
0 Posts
well i am a picture whore so here are some more haha
they sit right above the factory rack height, im not at home right now im at school so i had to use my redneck ruler (from knuckle to knuckle on your finger is about an inch).. so by that they are about 3" off the roof, not much of a diff. in the middle prob. about 2.75" or somethin, nothing real significant
they sit right above the factory rack height, im not at home right now im at school so i had to use my redneck ruler (from knuckle to knuckle on your finger is about an inch).. so by that they are about 3" off the roof, not much of a diff. in the middle prob. about 2.75" or somethin, nothing real significant
#10
Registered User
Join Date: Jun 2005
Location: Rocky Top, Tennessee
Posts: 501
Likes: 0
Received 0 Likes
on
0 Posts
oh yea and here is my setup as of now...
8000124 Q Towers
8000410 66" Cross Bars
8000662 Q 62 Clips
8007045 44" Fairing
8002085 Raptor (x2)
hoping to add a basket on that for Christmas though
8000124 Q Towers
8000410 66" Cross Bars
8000662 Q 62 Clips
8007045 44" Fairing
8002085 Raptor (x2)
hoping to add a basket on that for Christmas though
Thread
Thread Starter
Forum
Replies
Last Post
LittleUgly
86-95 Trucks & 4Runners (Build-Up Section)
15
01-02-2020 01:30 PM
charlie_fong
General Vehicle Related Topics (Non Year Related)
0
09-27-2015 10:06 PM
FS[PacNorWest]: 1987 4Runner SAS, 22RE, 5Spd, Dual Cases, etc
toyotasaurus
Vehicles - Trailers (Complete)
0
09-24-2015 03:30 PM