Cool rear bumper for 1st gens or trucks
#1
Cool rear bumper for 1st gens or trucks
Actually this design would work on just about any Toy with some fabbing.
Saw this on Cascade's site, and that guy pulled it from the Snort site.
Nice clean simple style.
I don't need a tire carrier, so something clean and simple like this is nice, and I like it better than some of the round tube styles for the rear I have seen.
Saw this on Cascade's site, and that guy pulled it from the Snort site.
Nice clean simple style.
I don't need a tire carrier, so something clean and simple like this is nice, and I like it better than some of the round tube styles for the rear I have seen.
#2
Registered User
Join Date: Sep 2002
Location: Poway, CA
Posts: 572
Likes: 0
Received 0 Likes
on
0 Posts
My only concern with that is that the bumper seems so short. I mean it's probably just me, but I'd like a bit more metal hanging down on there. I mean what if some little civic or other smallish car rear ended him? It would go under his truck, and hit axel That's just me though, A little overly paranoid
Although it is a very nice looking bumper, I really like the rear slider type things on the corners I actually saw one that a guy was fabbing a rear bumper up over on XOC, it pretty much replaces the center section of the bumper (The Xterras have a center bumper piece, and the end cap things just like the 2nd 4Runners) and it looked really cool. If i had any welding/machining skills I would make one for myself
-Braden
Although it is a very nice looking bumper, I really like the rear slider type things on the corners I actually saw one that a guy was fabbing a rear bumper up over on XOC, it pretty much replaces the center section of the bumper (The Xterras have a center bumper piece, and the end cap things just like the 2nd 4Runners) and it looked really cool. If i had any welding/machining skills I would make one for myself
-Braden
#3
I think he has that one short on purpose by looking at his rig.
Looks like it's setup for some serious off road duty, so he made it short so it would not kill his approach angle going up a steep incline.
Yeah, if I had one built like that, it would hang down a bit more, but not much.
Gotta get those huge new backup lamps of mine up higher
Looks like it's setup for some serious off road duty, so he made it short so it would not kill his approach angle going up a steep incline.
Yeah, if I had one built like that, it would hang down a bit more, but not much.
Gotta get those huge new backup lamps of mine up higher
#5
Banned
Join Date: May 2002
Location: Colorado Springs
Posts: 2,617
Likes: 0
Received 0 Likes
on
0 Posts
Looks like a homegrown deal to me. Made from the same material that his rock sliders are. There's no light on the liscence plate for night driving. Around here that will get you pulled over. Aside from that it looks pretty sweet.
Trending Topics
#8
Contributing Member
That's a very clean design. I like it-- but would prefer to see a license plate mount. Probably could be done pretty easily though. To me it looks like the owner would have to cut into the bodywork just under the tailgate to get the bumper to fit up so close to the body without have brackets hanging down. I would definitely like to see what it looks like from the underside if you find any more pics Corey.
I hate my rear bumper, and want a new one. I'm not too wild about All Pro's design, and I really haven't seen too many good looking rear bumpers for this generation of trucks, except for this one.
I hate my rear bumper, and want a new one. I'm not too wild about All Pro's design, and I really haven't seen too many good looking rear bumpers for this generation of trucks, except for this one.
#11
Cool, is he up North by you Mike?
Hopefully I can get some more pics from him.
Something like that and with a receiver hitch below, and the two tow points on each side like Churnd said would do it for me.
I have the license plate built into the tailgate, so no worries there.
Hopefully I can get some more pics from him.
Something like that and with a receiver hitch below, and the two tow points on each side like Churnd said would do it for me.
I have the license plate built into the tailgate, so no worries there.
#13
Registered User
Join Date: May 2002
Location: Seattle
Posts: 3,000
Likes: 0
Received 0 Likes
on
0 Posts
I like it.
I've been playing around with some ideas in SolidWorks lately, itchin' for something to make with my new welder. Fired it up saturday night on some scrap and promptly emanated a classic Tim Allen grunt, didn't know I could weld that pretty.
I've been playing around with some ideas in SolidWorks lately, itchin' for something to make with my new welder. Fired it up saturday night on some scrap and promptly emanated a classic Tim Allen grunt, didn't know I could weld that pretty.
#15
Registered User
Join Date: May 2002
Location: Seattle
Posts: 3,000
Likes: 0
Received 0 Likes
on
0 Posts
It's primarily 3d CAD but can also do 2d and exploded drawings. I um... found it? I like it a heck of a lot more than AutoCAD, lots easier to use once you learn the interface.
#16
That is a cool design Shane you drew.
Hey, as soon as I saw this guy's truck, it reminded me of yours.
http://www.pnw4runners.net/runs/7602/201024.jpg
http://www.pnw4runners.net/runs/7602/181024.jpg
Hey, as soon as I saw this guy's truck, it reminded me of yours.
http://www.pnw4runners.net/runs/7602/201024.jpg
http://www.pnw4runners.net/runs/7602/181024.jpg
#18
Registered User
Join Date: May 2002
Location: Seattle
Posts: 3,000
Likes: 0
Received 0 Likes
on
0 Posts
Originally posted by Corey
That is a cool design Shane you drew.
That is a cool design Shane you drew.
hint: It's not a license plate, it's a placeholder for something else that I haven't drawn out yet...