Throttle position sensor adjustment (NEED HELP) - YotaTech Forums
YotaTech Forums  

Go Back   YotaTech Forums > Toyota Forums Available > Toyota SUV & Truck Tech > General Electrical & Lighting Related Topics

Welcome to Yotatech!
Welcome to Yotatech,

You are currently viewing our forum as a guest, which gives you limited access to view most discussions and access our other features. By joining our community, at no cost, you will have access to post topics, communicate privately with other members (PM), respond to polls, upload content and access many other special features. Registration is free, fast and simple, so please join our community today!


Reply
 
Thread Tools Search this Thread
Old 10-13-2009, 02:42 PM   #1 (permalink)
Registered User
 
Join Date: Sep 2009
Location: Athens, GA
Posts: 5
Throttle position sensor adjustment (NEED HELP)

I am having trouble adjusting the new TPS on my 22re. I printed something about it off the net but its really confusing. Anyone have any step by step intructions to do this. The truck is falling on its face spitting and spuddering aroung half throttle.
This ad is not displayed to registered members.
Register your free account today and become a member on Yotatech!
kawabays is offline  
Digg this Post!Add Post to del.icio.usBookmark Post in TechnoratiFurl this Post!
Reply With Quote
Old 10-13-2009, 03:09 PM   #2 (permalink)
Contributing Member
 
4Crawler's Avatar
 
Join Date: Jun 2002
Location: SF Bay Area, CA
Posts: 7,828
See below:
- http://www.4crawler.com/4x4/CheapTri...#TPSAdjustment

And at the end of that section is a simplified 10 step procedure:

Quote:
Throttle Position Sensor IDL-E2 Adjustment Procedure (courtesy of Frankenyota):

1. Loosen both screws attaching TPS to throttle body.
2. Attach multi-meter to TPS terminals IDL and E2 (the bottom two terminals on the TPS). You can use alligator clips to make this easier or use small ¼” lengths of vacuum hose to hold them on
3. Insert 0.85mm (22RE) or 0.77mm (3VZE) feeler gauge between throttle stop screw and throttle plate (see picture)
4. Move TPS body CW/CCW until ohms reading on multimeter is infinite (open)
5. Move the TPS body very slowly CCW until you find the end of the resistive strip, the meter will indicate <2.3Kohms of resistance
6. Move the TPS body extremely slowly in the CW direction until the meter goes to open/infinite again
7. Tighten the top TPS screw being very careful not to disturb the adjustment
8. Remove the feeler gauge and insert a 0.57mm (22RE) or 0.50mm (3VZE) feeler gauge
9. The meter should (hopefully) indicate between 0 and 2.3Kohms of resistance, if it does tighten the bottom screw and reconnect the electrical connector, if not go back to step 4 and try again
10. To check whether the adjustment was successful start the engine and insert the timing test jumper, if the idle speed decreases audibly it is working normally.
__________________
1985 Toyota 4Runner SR-5, 22REC engine, dual t-cases, 4.88 gears, dual ARBs, 33x10.50 BFGs or 35x12.50 MTRs
r.c.brown@ieee.org
TruckEditor@tlca.org
Project: 4Crawler
4Crawler OffRoad
Gettin'Off 4WD Club
4Crawler is offline  
Digg this Post!Add Post to del.icio.usBookmark Post in TechnoratiFurl this Post!
Reply With Quote
Old 10-13-2009, 03:48 PM   #3 (permalink)
Registered User
 
Join Date: Sep 2009
Location: Athens, GA
Posts: 5
Thanks that's a lot better!
kawabays is offline  
Digg this Post!Add Post to del.icio.usBookmark Post in TechnoratiFurl this Post!
Reply With Quote
Reply

Tags
adjustment, positioning, sensor, throttle

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


All times are GMT -8. The time now is 12:02 AM.


Powered by vBulletin® Version 3.7.4
Copyright ©2000 - 2009, Jelsoft Enterprises Ltd.
Search Engine Optimization by vBSEO 3.1.0
Powered by vbWiki Pro . Copyright ©2006, NuHit, LLC
2009 InternetBrands, Inc.