NO ENGINE PARTS

I'm parting out a clean 1991 22re. I bought it from a guy who took the engine out of it before he sold it to me. Though it's obviously wrecked, I saw the engine run and drove the truck before buying. He took the engine out later and sold it to me. I bought it in order to get rid of the stupid looking gangster rims on my own truck, as well as grab a few body parts.

Located in Marion, Kansas.

I'm thinking most suspension parts can be shipped for around $50 based on location, everything else we can just do what I usually do with used parts, which is sell it for about 50% of the RockAuto price, depending on how hard it is to get to. I hope this pricing is specific enough, as I don't want my post deleted. Mods, please inform me if more specific information is needed.

VIN is JT4RN81A9M5113806

 

How much for the A/C hoses and all the factory tie downs from the bed? Shipping zip code is 97361.

Can you do me a favor and measure the motor mounts to the front of the frame horn? I also would really appreciate it if you could lay a tape measure across the frame so I can see the top of the upper control arm and the motor mount. I have been looking for this measurement and have had a hard time finding someone who would do this for me.

Thanks,

85Toyman

 

Would you cut pieces of sheet metal out of the bed? I need sections infront of and behind the wheels

 

Toyman, I'll get those measurements for you. And I'll get the hoses off and weighed and see how much it costs to ship as well.

nbl, I'd be fine cutting into the frame as well. PM me more specifics about which cuts you want. Also, are you wanting them shipped?

 

Yes shipped please I'll throw up a tape measure when I get home and post some pics

 

Ok so the pieces I need are.



The front left and right side cut straight down about that far in and cut straight across the top of the divot to the wheel well

 

The rear behind the wheel on both sides



In 12 inches from the taillight cut straight down and straight across the top of the divot to the wheel well.

These cuts don't have to be very precise torch cut or sawzall would be fine. Before you cut how much will this run me?

 

Ok nbl, so I'm still not quite sure, I think you are saying you just want the bed side, right? Or would you like me to cut the entire bed horizontally from that point? In either case, I'd say $120 plus shipping? It doesn't matter to me how much you take, since the rest will just go to scrap. Let me know how that sounds

 

How is the wiring ? I am looking for the Integration relay with the harness connectors and as much harness wire as practical. It's behind the passenger kick panel, and some of the harness goes thru the firewall/side.
Thanks,
Steve

 

How about the battery tray support sheetmetal? The little platform on the passenger wheel well that is spot welded on? Mine is completely rotted away, but my fender survived it. You could just crudely cut away the fender around it and I'd drill the spot welds if it's in decent shape.

Oh, and what about the speedometer cable?

These parts would be shipped to Louisiana, 70360.

 

Stephen, Super, I believe all the parts you are asking for are available, and I can start pulling them when we discuss price. I'll PM you both!

 

how much for the seat belts

 

You got the shifter and knob? Pics of it?

 

Joey- I PMed you prices.

jzx81- Sorry I do not have the shifter or knob.

 

Is the tailgate pretty straight and rust free? Shipping would be to 49506

thanks

 

How are the sunvisors? Can you get pics?

 

Sorry for the long reply time Aberle, I've been dealing with a few potential buyers for the bed who keep backing out. Tailgate is straight and rust free. I've stolen the access panel off of it for my own truck though, will that be a problem?

And I'll get you some pictures of the sunvisors I8URSVT. They are in good condition.

 

Post pics of visors once you get them. Thanks

 

Visor pics for I8uRSVT

 

thanks for the reply but I found a brand new one off craigslist.