Pre 84 Trucks 1st gen pickups

w56-a/b into 1st gen truck help

Thread Tools
 
Search this Thread
 
Old 04-19-2012, 06:31 PM
  #1  
Registered User
Thread Starter
 
82shorty's Avatar
 
Join Date: Nov 2008
Location: brooks alberta canada
Posts: 85
Likes: 0
Received 0 Likes on 0 Posts
w56-a/b into 1st gen truck help

im in the middle if putting a w56a into my 82 since the l50 broke a tooth in first gear and a week later snapped off the clutch fork and i got a good deal on the w56a. Ive order the crossmember from Budbuilt to fit this swap. All new seals and shifter bushings from Marlin and have it all cleaned up and ready to install. My questions are: i know i have to resize my driveshafts but on the rear ive lifted it 4" at the same time as the tranny went back 4". Is this going to be enough to have the rear shaft relenghtened or will it still be ok? should i have it done with a long spline kit anyway due to the added flex of the chevy springs. Ive been running the 63"s for a year w/4" shackle but have installed a 7" now to match the front lift im doing now (tg"springs,5"shackles). I know i need to redo the front shaft with a long spine one as it is midway thru a 4" spring lift. Does anyone have a template for cutting the shifter holes ive measured and looked and it looks like my trans shifter will sit in the tranfer case hole and i just have the one hole to cut but it would be nicer if someone had a template or something to measure/cut from. Who else has done this swap?
Old 04-20-2012, 05:41 PM
  #2  
Fossilized
Staff
iTrader: (6)
 
dropzone's Avatar
 
Join Date: Oct 2005
Location: PNW
Posts: 19,771
Received 448 Likes on 293 Posts
yes you will need to redo your rear shaft. install trans and than measure flange to flange
Old 04-20-2012, 05:50 PM
  #3  
Registered User
iTrader: (1)
 
slacker's Avatar
 
Join Date: Jan 2006
Location: BC Canada
Posts: 6,300
Received 274 Likes on 185 Posts
heyyyy .. Brooks AB. my ol' stompin' grounds !!
just a "drive by" shout out !!



.
Old 04-20-2012, 05:54 PM
  #4  
Registered User
Thread Starter
 
82shorty's Avatar
 
Join Date: Nov 2008
Location: brooks alberta canada
Posts: 85
Likes: 0
Received 0 Likes on 0 Posts
im waiting for a throw-out bearing clip to come from Marlin then i can get the trans in place. i was just thinking that if the trans went back 4" at the same time therearend went down 4" i should still be somewhat close to the stock lenght. im just worried the extra flex will be more then the slip spline can handle
Old 04-20-2012, 05:55 PM
  #5  
Registered User
Thread Starter
 
82shorty's Avatar
 
Join Date: Nov 2008
Location: brooks alberta canada
Posts: 85
Likes: 0
Received 0 Likes on 0 Posts
where did you wheel aroiund here slacker? its TO Flat lol
Old 04-21-2012, 03:37 PM
  #6  
Registered User
iTrader: (1)
 
slacker's Avatar
 
Join Date: Jan 2006
Location: BC Canada
Posts: 6,300
Received 274 Likes on 185 Posts
never wheeled there , it was before I had my DL .. many moons ago
but I do remember the old aquaduct , dont know if it's still there or not , but we use to walk the train tracks out to the mid pump station and fish for pike .. gopher hunting when they use to pay 5C a tail . grade 7-8-9-10 and my first KISS concert in Lethbridge .. good times and fond memories



.
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
4x4-runner
The Classifieds GraveYard
14
02-26-2017 06:42 AM
TACORICAN
84-85 Trucks & 4Runners
5
07-06-2015 04:44 PM
chbarnha
86-95 Trucks & 4Runners
5
06-18-2015 10:23 AM
esun127
95.5-2004 Tacomas & 96-2002 4Runners
1
07-18-2002 07:53 PM



Quick Reply: w56-a/b into 1st gen truck help



All times are GMT -8. The time now is 09:00 PM.