YotaTech Forums - Search Results

Notices
Search: Posts Made By: MacGyver!
Showing results 1 to 18 of 18
Search took 0.04 seconds.
11-27-2013, 12:51 PM
Replies: 24
Views: 37,905
Posted By MacGyver!

Thanks!

Thanks!
11-14-2013, 09:14 AM
Replies: 5
Views: 818
Posted By MacGyver!

I've replaced that firewall seal on my '92...

I've replaced that firewall seal on my '92 pickup. If it is torn/cracked the cabin get very noisy from all the sounds coming from the engine compartment.

It's pretty easy to replace and I think...
11-13-2013, 01:30 PM
Replies: 18
Views: 3,361
Posted By MacGyver!

Quick Update: I finally decided to take the...

Quick Update:

I finally decided to take the truck to a mechanic. He found a vacuum leak and, upon inspection, found that several of the vacuum lines had been incorrectly connected (lines going to...
04-28-2012, 03:14 PM
Replies: 9
Views: 2,004
Posted By MacGyver!

Sorry for the late reply, the part number that I...

Sorry for the late reply, the part number that I got from the dealer is 69751-12030-J0, they had to order it for me; I still haven't installed them yet, too many other things to do. Let me know if...
03-28-2012, 09:55 PM
Replies: 18
Views: 3,361
Posted By MacGyver!

Sorry to hear the new EGR didn't fix the problem....

Sorry to hear the new EGR didn't fix the problem. You may want to look into what 4crawler said, but I am pretty sure my problem (which is similar to yours) has to do with the EGR system, primarily...
03-27-2012, 04:20 PM
Replies: 18
Views: 3,361
Posted By MacGyver!

Awesome, I hope to hear good news after you...

Awesome, I hope to hear good news after you install. Keep me updated.
03-22-2012, 05:52 PM
Replies: 18
Views: 3,361
Posted By MacGyver!

I checked the dash pot and it was a little bit...

I checked the dash pot and it was a little bit out of spec (while plugged, upon throttle release it would hold at about 1400 rpm instead of 2000 rpm); I adjusted it to spec...unfortunately, the low...
03-21-2012, 12:41 PM
Replies: 18
Views: 3,361
Posted By MacGyver!

4Crawler, thanks for the input. I'll check that...

4Crawler, thanks for the input. I'll check that next.

masterbasch, checking the timing certainly couldn't hurt. I checked the ignition timing before moving onto the EGR (didn't check the cam...
03-20-2012, 10:28 AM
Replies: 18
Views: 3,361
Posted By MacGyver!

I pulled a slight vacuum on the EGR (1-2 in Hg)...

I pulled a slight vacuum on the EGR (1-2 in Hg) and it was enough to open the valve and cause poor idle. I'm going to check the VSV valve per fsm and inspect the throttle body. If this stuff checks...
03-18-2012, 08:24 PM
Replies: 18
Views: 3,361
Posted By MacGyver!

So, I ran a test this weekend: I placed a...

So, I ran a test this weekend: I placed a t-fitting on the vacuum line going into the egr valve. I then drove the truck under conditions that I noticed the low idle and had a partner read off the...
03-13-2012, 03:19 PM
Replies: 7
Views: 7,146
Posted By MacGyver!

Also interested in this. Where did you...

Also interested in this.

Where did you obtain all of the parts? Ebay? Junkyard? Dealer?
03-13-2012, 12:55 PM
Replies: 13
Views: 1,580
Posted By MacGyver!

I'm also interested in doing this.

I'm also interested in doing this.
03-13-2012, 12:21 PM
Replies: 18
Views: 3,361
Posted By MacGyver!

So, I believe I found the underlying issue: I...

So, I believe I found the underlying issue: I eventually traced the problem to the EGR valve. To test, I disconnected the vacuum line and the momentary low idle when coming to a stop vanished, when...
03-12-2012, 02:32 PM
Replies: 9
Views: 2,004
Posted By MacGyver!

Thanks for the advice. I'll probably try to use...

Thanks for the advice. I'll probably try to use a flat tip on a soldering iron to melt the post. If I come across any earth shattering revelations, I'll be sure to share.
03-11-2012, 05:18 PM
Replies: 9
Views: 2,004
Posted By MacGyver!

Yeah, I was thinking the same thing about the...

Yeah, I was thinking the same thing about the melting. I'm not sure how I would do that or what to epoxy it too.
03-11-2012, 04:18 PM
Replies: 9
Views: 2,004
Posted By MacGyver!

Lock Knob Holder Install?

I cannot seem to install the lock knob holder (trim around lock knob on doors, my driver side was missing when I bought it). Does anyone know how to do this? It seems so easy, but it just keeps...
02-26-2012, 10:06 PM
Replies: 133
Views: 347,263
Posted By MacGyver!

The 91 octane rating is for RON designation, in...

The 91 octane rating is for RON designation, in the USA and Canada we use AKI. A RON 91 rating is equivalent to an AKI 87 rating. So 87 octane in the USA and Canada is the correct fuel.
...
02-06-2012, 03:01 PM
Replies: 18
Views: 3,361
Posted By MacGyver!

Momentary Low Idle

Hey guys, I'm new to the forum (and Toyotas) and have an idle question:

When I push in the clutch while coming to a stop (or just coasting) the rpms drop down below the normal idle speed for about...
Showing results 1 to 18 of 18


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.