YotaTech Forums - Search Results

Notices
Search: Posts Made By: BMarino
Showing results 1 to 22 of 22
Search took 0.01 seconds.
05-02-2019, 06:14 PM
Replies: 20
Views: 1,117
Posted By RAD4Runner

Looks good, O.P. Like Old87yota says. Just make...

Looks good, O.P.
Like Old87yota says. Just make sure you have enough slack so there'll be no tension in case battery shifts.
On mine, the stock FL wire does not run under the battery hold downs....
05-02-2019, 03:07 PM
Replies: 20
Views: 1,117
Posted By Co_94_PU

You will want to cycle the steering from steering...

You will want to cycle the steering from steering stop to steering stop regardless, this is the bleed/purging procedure. There is a substantial amount of fluid in that line which means when you put...
05-02-2019, 10:12 AM
Replies: 20
Views: 1,117
Posted By old87yota

RAD4Runner's suggestion applies to making your...

RAD4Runner's suggestion applies to making your own fusible link wire. Since you have a Toyota one, you just hook up one end to the battery and the other (metal plate end) to the fuse box.

:safari:
05-01-2019, 07:45 PM
Replies: 20
Views: 1,117
Posted By Melrose 4r

There is an o-ring on the nipple for the feed...

There is an o-ring on the nipple for the feed line(larger hose) to the ps pump. The nipple is held to the pump with one bolt. This o-ring is a common source of leak.
04-05-2019, 10:39 AM
Replies: 20
Views: 1,117
Posted By Co_94_PU

Agree, it is a fused cable like those used to...

Agree, it is a fused cable like those used to supply a high-power audio amplifier. The inner positive cable you should be able to trace into the cabin somewhere. I can see it routes under the...
03-25-2019, 07:57 AM
Replies: 12
Views: 621
Posted By scope103

Here's the FSM page for adjusting the pre-load of...

Here's the FSM page for adjusting the pre-load of the axle nut. http://web.archive.org/web/20120424234339/http://personal.utulsa.edu/~nathan-buchanan/93fsm/suspensionandaxle/5frontaxl.pdf You'll need...
03-25-2019, 07:43 AM
Replies: 12
Views: 621
Posted By millball

Further consultation of my '95 4Rnner FSM says to...

Further consultation of my '95 4Rnner FSM says to torque the nut to 43fp and rotated the hub a couple times before loosening the nut and retorquing to 18fp and checking preload.

Outer nut to be...
03-04-2019, 06:07 AM
Replies: 3
Views: 353
Posted By millball

Don't know for sure, but I expect that they help...

Don't know for sure, but I expect that they help to facilitate handling the axle during forging and subsequent machining operations.
02-28-2019, 10:33 AM
Replies: 17
Views: 1,375
Posted By Kolton5543

I didn't realize how small the nick really was....

I didn't realize how small the nick really was. With it being that small and that close to the snap ring groove, I think it will be fine. Right at that grove, there will be little to no power...
02-27-2019, 06:18 PM
Replies: 17
Views: 1,375
Posted By scope103

Gee, I dunno. I suppose I'd use the "nicked"...

Gee, I dunno. I suppose I'd use the "nicked" shaft and just be careful. I think I would take a file and try to round off all the sharp corners (it looks like the bottom of the "nick" is close to...
02-06-2019, 04:20 PM
Replies: 22
Views: 2,317
Posted By millball

Unless there is severe corrosion or some sort of...

Unless there is severe corrosion or some sort of severe mechanical deformation of the bearing case, the bearing is a very light fit into the case, and little, or no force is required to get it out of...
02-06-2019, 02:31 PM
Replies: 22
Views: 2,317
Posted By RAD4Runner

Illustrated examples above....

Illustrated examples above. (https://www.yotatech.com/forums/f116/question-reusing-rear-axle-bearings-have-been-pressed-out-302283/#post52417700)
01-24-2019, 05:15 PM
Replies: 17
Views: 1,375
Posted By millball

My '95 4Runner has 4 wheel ABS. It has rear...

My '95 4Runner has 4 wheel ABS. It has rear axles with tone rings.

My wrecked '92 has 2 wheel ABS that uses the rear ring gear and sensor on the 3rd member.
01-24-2019, 12:29 PM
Replies: 17
Views: 1,375
Posted By scope103

Frankly, I don't know much about which "gen" a...

Frankly, I don't know much about which "gen" a particular truck or 4runner is. The rear axle depends on the body style, but for a given style the same axle fits 1988-2006. Yes, even those with the...
01-24-2019, 12:11 PM
Replies: 17
Views: 1,375
Posted By Kolton5543

The 3rd gens I believe have 4 wheel ABS. Some...

The 3rd gens I believe have 4 wheel ABS. Some even get their speedo signal from there. The 2nd gens were available with a reletively crude version of rear ABS. Their sensor is on the third member...
01-18-2019, 10:56 AM
Replies: 17
Views: 1,375
Posted By Kolton5543

Most of the force is going to be transmitted...

Most of the force is going to be transmitted through the outer diameter of the shaft. A deep cut in it will create a weak spot on the outer edge and can cause issues. A nick like that can have a much...
11-13-2018, 08:39 PM
Replies: 15
Views: 1,613
Posted By cbh148

Here ya go ...

Here ya go

https://cimg5.ibsrv.net/gimg/www.yotatech.com-vbulletin/640x480/image7_efda3f177a25c70b35e67cd8ff73b557715b35e0.jpg...
11-13-2018, 02:17 AM
Replies: 15
Views: 1,613
Posted By ev13wt

Frame and cab will always move together, because...

Frame and cab will always move together, because they are attached in an unmovable fashion.

OP Look at your upper A arm mounts, specifically the rear one, compare those to the other side.

I do...
11-12-2018, 03:29 PM
Replies: 15
Views: 1,613
Posted By Co_94_PU

Good photos cbh, A good example of a flat lower...

Good photos cbh,
A good example of a flat lower control arm in that short from the right side you can see both and they are not equal.

Some of this photos I find a bit confusing. I thought you...
11-09-2018, 05:53 PM
Replies: 15
Views: 1,613
Posted By L5wolvesf

Yes to this being the primary problem. I would...

Yes to this being the primary problem. I would not be happy with the alignment shop not figuring it out especially considering they could not align it to specs.

But

Bent is not strong.
11-09-2018, 03:21 PM
Replies: 15
Views: 1,613
Posted By Co_94_PU

Its a bent frame. Adjusting the camber (in/out)...

Its a bent frame. Adjusting the camber (in/out) of the tire shouldn't effect the caster (fore/aft)..

You could measure it if you were inclined, the dimensions are in the service manual.

The...
11-08-2018, 08:47 AM
Replies: 1
Views: 1,160
Posted By scope103

Read the codes....

Read the codes. http://web.archive.org/web/20141031041050/http://personal.utulsa.edu:80/~nathan-buchanan/93fsm/engine/26diagnosi.pdf (There really is an SST as described in the manual, but we all use...
Showing results 1 to 22 of 22


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.