YotaTech Forums - Search Results

Notices
Search: Posts Made By: Kolton5543
Showing results 1 to 21 of 21
Search took 0.01 seconds.
06-02-2019, 10:39 PM
Replies: 32
Views: 3,160
Posted By Kolton5543

Last weekend we wheeled rug road from Mammoth to...

Last weekend we wheeled rug road from Mammoth to Pima. That trip was a blast. I'd upload photos from it too but it's not accepting them for some reason. I'll get it done when I get it to work. In the...
06-02-2019, 10:05 PM
Replies: 32
Views: 3,160
Posted By Kolton5543

This winter we had an extremely rare occurrence...

This winter we had an extremely rare occurrence where it snowed here. Here in Safford we usually only get snow that sticks once every four years or so. Usually its only an inch or two and hangs out...
06-02-2019, 09:47 PM
Replies: 32
Views: 3,160
Posted By Kolton5543

Made a spur of the moment trek up Tripp Canyon...

Made a spur of the moment trek up Tripp Canyon after work just in time to catch a sunset.
...
06-02-2019, 08:29 PM
Replies: 32
Views: 3,160
Posted By Kolton5543

Installed a fire extinguisher mount. Check...

Installed a fire extinguisher mount. Check original thread here: https://www.yotatech.com/forums/f88/fire-extinguisher-mount-307837/#post52424937
06-02-2019, 08:19 PM
Replies: 32
Views: 3,160
Posted By Kolton5543

Rear disk brake

Upgraded to rear disk brakes. I used my own design and it works well and was very inexpensive.

Here the original thread:...
Forum: The Fab Shop
06-02-2019, 08:00 PM
Replies: 0
Views: 1,648
Posted By Kolton5543

Budget But Effective Rear Disk Brake Upgrade

I recently decided it was time to do a rear disc brake swap. I got tired of my brakes fading to nothing everytime I crossed a deep wash and packed the drums full of sand. I considered the kits...
Replies: 10
Views: 2,557
Posted By Kolton5543

Thanks for mentioning TCP. I never heard of them....

Thanks for mentioning TCP. I never heard of them. They look to have some good reviews on their restoration shop paint and the price is right with lots of colors to choose from with a few that closely...
05-23-2019, 11:32 AM
Replies: 13
Views: 2,609
Posted By Kolton5543

The reverse lights switch commonly short out...

The reverse lights switch commonly short out internally. They usually will either short to ground or stick the lights on all the time. Unplug the switch, and jump the connector with a paper clip. If...
05-13-2019, 11:51 AM
Replies: 6
Views: 655
Posted By Kolton5543

I use a Snap-On Modis EEMS 300. It works good on...

I use a Snap-On Modis EEMS 300. It works good on anything pre 96. On my 94 it showed lots of different data. Has most of the stuff you'd find on regular OBDII cars inlcuding fuel trims, O2 voltage,...
05-01-2019, 11:40 AM
Replies: 17
Views: 939
Posted By Kolton5543

2wd and 4wd both have steering stops. If they're...

2wd and 4wd both have steering stops. If they're gone you should get some. The steering stops only make noise at full lock though. Ball joints can be very noisy sometimes. The lowers usually make the...
Forum: 3.4 Swaps
04-30-2019, 11:29 AM
Replies: 2
Views: 309
Posted By Kolton5543

3.4 clutch is a little bigger and will handle the...

3.4 clutch is a little bigger and will handle the power better. Honestly, a 3.0 clutch holds the 3.4 fine though. When doing a clutch job its best practice to buy a new flywheel anyway so that will...
04-22-2019, 11:32 AM
Replies: 8
Views: 475
Posted By Kolton5543

Its the heater hoses. The clamp is digging into...

Its the heater hoses. The clamp is digging into it like that, its because the hoes has started swelling. Cutting it short is just a temporary fix. To do it right, you should replace it. The clamp is...
02-28-2019, 10:33 AM
Replies: 17
Views: 1,374
Posted By Kolton5543

I didn't realize how small the nick really was....

I didn't realize how small the nick really was. With it being that small and that close to the snap ring groove, I think it will be fine. Right at that grove, there will be little to no power...
01-24-2019, 12:11 PM
Replies: 17
Views: 1,374
Posted By Kolton5543

The 3rd gens I believe have 4 wheel ABS. Some...

The 3rd gens I believe have 4 wheel ABS. Some even get their speedo signal from there. The 2nd gens were available with a reletively crude version of rear ABS. Their sensor is on the third member...
01-18-2019, 10:56 AM
Replies: 17
Views: 1,374
Posted By Kolton5543

Most of the force is going to be transmitted...

Most of the force is going to be transmitted through the outer diameter of the shaft. A deep cut in it will create a weak spot on the outer edge and can cause issues. A nick like that can have a much...
01-10-2019, 10:41 AM
Replies: 8
Views: 3,711
Posted By Kolton5543

If the old injectors and new injectors were...

If the old injectors and new injectors were tested good by your refurbisher, they're probably fine. FPR is the fuel pressure regulator. Pull the vacuum hose off of it and see if its wet with gas. If...
01-02-2019, 08:20 PM
Replies: 8
Views: 3,481
Posted By Kolton5543

Mine had gl-5 in it when I bought it. Shifted...

Mine had gl-5 in it when I bought it. Shifted smooth when I got it. After about year it started to get hard to shift. Eventually to the point where it almost couldn't be shifted without a good double...
12-04-2018, 10:27 AM
Replies: 3
Views: 977
Posted By Kolton5543

It's likely another failed VSS or the electrical...

It's likely another failed VSS or the electrical to it. Do the reverse lights work? They are powered on the same circuit. The ECU actually gets its speed input from the speedo. The speedo gets its...
09-26-2018, 08:45 PM
Replies: 8
Views: 698
Posted By Kolton5543

Yep, pickle forks and pitman arm pullers will...

Yep, pickle forks and pitman arm pullers will take care of those for you no problems. Both of which can be rented at most part stores.
09-18-2018, 08:28 PM
Replies: 8
Views: 491
Posted By Kolton5543

I've used an old belt an c-clamp before. Wrap the...

I've used an old belt an c-clamp before. Wrap the belt around the pulley tight and pinch the belt together tightly with a small c-clamp. Loop the other end of the belt around a nearby bolt or pulley...
07-24-2018, 11:06 PM
Replies: 4
Views: 426
Posted By Kolton5543

A flywheel should always be machined or replaced...

A flywheel should always be machined or replaced when installing a new clutch set. Most clutch warranties won't even be honored if a new flywheel wasn't bought on the same receipt or if there isn't...
Showing results 1 to 21 of 21


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.