YotaTech Forums - Search Results

Notices
 
Search: Posts Made By: Paul22RE
Showing results 1 to 25 of 47
Search took 0.00 seconds.
07-04-2019, 05:43 PM
Replies: 7
Views: 704
Posted By scope103

For $25, it might be worth avoiding the trip to...

For $25, it might be worth avoiding the trip to Napa. And while you can get really lucky and borrow a shrink-wrapped gauge, the whole point of "loaner" tools is that they are loaned out to people...
07-04-2019, 10:58 AM
Replies: 7
Views: 704
Posted By Co_94_PU

You get what you pay for in most cases. In this...

You get what you pay for in most cases. In this price range they aren't going to be well calibrated, or certificate calibrated. Which is generally fine. We're mostly concerned with major deviation...
07-02-2019, 08:10 AM
Replies: 18
Views: 1,657
Posted By SENOR NOODLES

Factory oil pressure is only about 4 to 5psi at...

Factory oil pressure is only about 4 to 5psi at idle. That is normal. They are lower oil pressure because they do not have lifters that need to be pumped up, or very many oil passages to send oil to...
07-02-2019, 07:36 AM
Replies: 18
Views: 1,657
Posted By 5 Fists

https://cimg5.ibsrv.net/gimg/www.yotatech.com-vbul...

https://cimg5.ibsrv.net/gimg/www.yotatech.com-vbulletin/2000x1504/20190702_054735_bcb1db2c2a07acec842d80723e79c0f5d5c21a42.jpg
That's where mine usually sits at idle, then up to just a hair under...
06-27-2019, 11:21 AM
Replies: 18
Views: 1,657
Posted By 5 Fists

That's about where mine sits at idle Paul, and...

That's about where mine sits at idle Paul, and goes up to just a hair under halfway when driving. I'll try to remember to snap a picture later today after I leave work and am up to operating temp.
06-26-2019, 02:43 PM
Replies: 18
Views: 1,657
Posted By scope103

I drive with 30w, and my needle doesn't get even...

I drive with 30w, and my needle doesn't get even that high at hot idle.

The spec for hot idle is 4.3psi...
06-17-2019, 07:37 AM
Replies: 30
Views: 2,345
Posted By scope103

While your fuel pressure does seem low, your...

While your fuel pressure does seem low, your gauge may not be that accurate anyway. The MFI system is designed to increase the injector open time when there is "too much" oxygen in the exhaust, so...
06-06-2019, 05:32 PM
Replies: 44
Views: 4,330
Posted By TLfromAI

OK I found a much simpler way to do this. The...

OK I found a much simpler way to do this. The trick is that the extra port on our diaphragm that goes to the power steering pump is not necessary. The diaphragm does nothing special for the power...
06-02-2019, 10:11 PM
Replies: 0
Views: 2,036
Posted By Spread5150

94 V6 clutch / flywheel replacement

So it was time for a new clutch at 198k. Took the truck in and ordered a New clutch kit from Rock Auto and a new Flywheel from LCE performance.

Since I purchased the truck at 194k I was uncertain...
05-02-2019, 08:28 PM
Replies: 3
Views: 333
Posted By RAD4Runner

Yep, measure resistance while dipped in boiling...

Yep, measure resistance while dipped in boiling water and then while dipped in crushed ice.
05-02-2019, 11:54 AM
Replies: 3
Views: 333
Posted By scope103

The coolant temps sensor is not a switch, it's a...

The coolant temps sensor is not a switch, it's a thermistor. (But you knew that, because you were testing resistance.) ...
05-02-2019, 11:46 AM
Replies: 3
Views: 333
Posted By Melrose 4r

I personally have had a HONDA coolant temp sensor...

I personally have had a HONDA coolant temp sensor fail and make the system think it was incredibly cold out, but the reading was still within the realm of possibility. So i'd take a couple readings...
02-19-2019, 09:30 AM
Replies: 2
Views: 525
Posted By 87-4runner

I know it doesn't sound very technical... but i...

I know it doesn't sound very technical... but i set my timing where my motors seem to like it the best... for optimal performance... whether that's 10, 12, 18... whatever it likes... make sense? It...
01-24-2019, 12:37 PM
Replies: 30
Views: 2,345
Posted By scope103

The 12mm banjo bolt is used at the fuel pressure...

The 12mm banjo bolt is used at the fuel pressure regulator.
https://cimg1.ibsrv.net/gimg/www.yotatech.com-vbulletin/1080x810/schraederconn_22532b4f274a1f91f8ef2b4acab4abba4f300b17.jpg
...
01-07-2019, 11:34 PM
Replies: 24
Views: 2,002
Posted By ev13wt

I''ve just put some very light oil on a paper...

I''ve just put some very light oil on a paper towl and "cleaned" the tb plate and housing where it sits at idle, leaving a thin film of oil. Also put some on the return spring, hoping it will flow...
01-07-2019, 03:21 PM
Replies: 24
Views: 2,002
Posted By Co_94_PU

EGR system shouldn't be functional at idle, or...

EGR system shouldn't be functional at idle, or while cold.

Pull the air hose off the front of the throttle body and try wiggling the throttle plate, try pushing it up down left right and in and...
01-07-2019, 05:54 AM
Replies: 24
Views: 2,002
Posted By snippits

I had a random high idle, and a new IACV fixed...

I had a random high idle, and a new IACV fixed that.

My 92 does the same thing randomly on hot start. My throttle body is clean as it gets. I have come to the conclusion that it's probably wobble...
01-07-2019, 05:34 AM
Replies: 24
Views: 2,002
Posted By ev13wt

Sure the vaccum lines under the pot and egr...

Sure the vaccum lines under the pot and egr system are attached, attached correctly? Get some OEM vac lines and replace everything.
Recheck TPS. If not tightened down TPS screws before
Measure the...
11-17-2018, 11:14 AM
Replies: 24
Views: 2,002
Posted By Co_94_PU

pcv vent hose. Not part of the idle control. ...

pcv vent hose. Not part of the idle control.

On the older model... The air passage is accessible from a large hose on the front.
11-17-2018, 10:56 AM
Replies: 24
Views: 2,002
Posted By Co_94_PU

wait what?? I dunno how you plumbed this but...

wait what??

I dunno how you plumbed this but my idle valve lines do not go to the valve cover. It should run from one side of the throttle plate to essentially the other.
I'm gonna go try and dig...
11-17-2018, 10:24 AM
Replies: 24
Views: 2,002
Posted By Co_94_PU

Iacv shouldn't have any effect, it's fully closed...

Iacv shouldn't have any effect, it's fully closed when warm. You can verify its sealing if you really want to by trying to pass air thru the front air hose.

You touch the throttle and the idle...
11-06-2018, 09:09 PM
Replies: 3
Views: 1,305
Posted By Co_94_PU

This is the wrong diagram but it's similar, in...

This is the wrong diagram but it's similar, in the first gen 4runner diagram it's labeled as N#.. (Engine harness is number 2)
...
11-06-2018, 03:22 PM
Replies: 3
Views: 1,305
Posted By Co_94_PU

I don't have that FSM handy, but it's part of the...

I don't have that FSM handy, but it's part of the dash harness. From memory that is the smaller plug in the right hand kick panel.
11-05-2018, 04:08 PM
Replies: 11
Views: 1,317
Posted By Co_94_PU

Assuming it was actually the knock sensor wire...

Assuming it was actually the knock sensor wire you grounded, no damage would be done since the knock sensor output is an AC wave zero volts is an acceptable input for the ECU.

I don't think my 94...
11-05-2018, 02:51 PM
Replies: 11
Views: 1,317
Posted By Co_94_PU

If you have a tach you have an oil pressure...

If you have a tach you have an oil pressure gauge, no idiot light.

Looking at the intake side of the 22re, through the wheel well, to the left of the oil pressure sending unit (and slightly...
Showing results 1 to 25 of 47
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.