can someone take a picture of the wiring behind the kick plate
02-28-2009, 03:38 PM
#1
Registered User
Thread Starter
can someone take a picture of the wiring behind the kick plate
I had a aftermarket alarm that I removed.
This pic I have one wire with connector and the other one was cut.
This shows all of it after the removal.
before removal
and what was removed. I am not sure I got it all or that I got too much.
This pic I have one wire with connector and the other one was cut.
This shows all of it after the removal.
before removal
and what was removed. I am not sure I got it all or that I got too much.
02-28-2009, 03:50 PM
#2
Registered User
Join Date: Dec 2007
Location: Rochester, Washington
Posts: 500
Likes: 0
Received 0 Likes
on
0 Posts
02-28-2009, 03:52 PM
#3
Registered User
Thread Starter
Everything works Except the turn signals and hazard lights. I know all the bulbs are good. So I have a feeling i am missing a connection or missing a wire.
Trending Topics
02-28-2009, 04:32 PM
#8
Registered User
Join Date: Dec 2007
Location: Rochester, Washington
Posts: 500
Likes: 0
Received 0 Likes
on
0 Posts
Does your horn work?
Mine is a 01 4Runner V6
I've got two possibilities
#24 Turn signals/Hazard flashers and #31 Horn/Hazard flashers
Pic from my owners manual.......
Mine is a 01 4Runner V6
I've got two possibilities
#24 Turn signals/Hazard flashers and #31 Horn/Hazard flashers
Pic from my owners manual.......
02-28-2009, 05:54 PM
#12
Registered User
Join Date: Dec 2007
Location: Rochester, Washington
Posts: 500
Likes: 0
Received 0 Likes
on
0 Posts
I'm going to guess the turn 10A covers the emergency flashers too.
So it was good?
You might want to double check against your owners manual, if you've got one.
Did your turn signals flash with the alarm turning off or on?
If the alarm controlled the lights at all, I would think you would need to hook some wires back up.
So it was good?
You might want to double check against your owners manual, if you've got one.
Did your turn signals flash with the alarm turning off or on?
If the alarm controlled the lights at all, I would think you would need to hook some wires back up.
02-28-2009, 06:11 PM
#13
Registered User
Thread Starter
All fuses good. I know i am missing a wire or something somewhere. Both turn and hazards are out so that tells me its something I disconnected. But I am unsure if when prior owner installed the alarm that he removed one of the wires and replaced it with the alarm harness.
03-01-2009, 11:13 AM
#17
Registered User
Join Date: Mar 2004
Location: Vancouver
Posts: 2,171
Likes: 0
Received 0 Likes
on
0 Posts
03-01-2009, 12:27 PM
#18
Registered User
Thread Starter
Head in ass situation. I did not check to see if I had pulled the wires off the hazard switch, I pulled it up and bam all was working fine. If I had been the one that installed this kit I would have had no problem taking it out. But the dealer lost the fob for it and just unplugged what they thought was right. So I got in the middle of this and had to work around and though it. But now I can tell you what every wire in the dash does and where it can be found.
Thread
Thread Starter
Forum
Replies
Last Post
jasonty
Pre 84 Trucks (Build-Up Section)
41
12-23-2018 01:00 PM
BeMiceElf
Misc Stuff (Vehicle Related)
7
10-10-2015 09:40 PM
88yodabasket
86-95 Trucks & 4Runners
15
07-13-2015 01:32 PM
