Last edit by: IB Advertising
See related guides and technical advice from our community experts:
Browse all: Toyota 4Runner Tire Repair and Maintenance
- Toyota 4Runner, Tacoma, and Tundra: Why is the Tire Pressure Light On?
Guide to diagnose trouble and recommended solutions.
Browse all: Toyota 4Runner Tire Repair and Maintenance
What PSI (pressure) are you running?
#141
265/75/16 D's on a 92 reg. cab shortbed stock gears 35psi checkem if they look low. last trip 12 hrs 1 day best tank 23mpg's. i spent 2.5 years in a tire store max psi on side wall of tire is always cold and a 10 ply E load is always going to be harsh on a yota id air em way down 25 to 30 ish if you like ur teeth
#142
Registered User
haha, dont mean to change topic, but i literally lol'd.
but i air my 35x12.'5s up to 35 psi. do equal on road as i do off. and off-road i do just "surface mud" trails, so its perfect for me
if i ever know i'm gonna venture off trail, i'll just keep going till i start gettin bad traction, then i'll pull out my knife and airdown
Last edited by 85gijunk4x4; 09-04-2011 at 05:17 PM.
#146
I'm running 65 psi in my Guard Dogs because that's what the shop put in them when they were mounted, but I'm thinking 65 is a lot for such a light truck especially when it's unloaded-should I run 45-50 when I'm not hauling?
#151
Registered User
Join Date: Feb 2013
Location: Hampton VA
Posts: 167
Likes: 0
Received 0 Likes
on
0 Posts
Wow, a lot of people in this thread that have no idea. Airing up the tire too much causes the contact patch to be in the middle of the tire. Not only does this cause premature wear, it is also dangerous. Since you have less rubber on the road your stopping distance, and wet weather performance is greatly diminished. The best rule of thumb is to start at the door jam pressures, and adjust slightly for performance, and ride quality.
Many tricks for checking the contact patch. NEVER NEVER run the max PSI that is printed on the sidewall. This is the max cold pressure for maintaining maximum load capacity of the tire, and that rating will be much more than any of the Yota's here are rated for.
ALSO, anyone running more than 45 pounds on a standard valve stem is asking for trouble. Standard valve stems are only rated for 45-50 PSI, larger 3/4 and 1 ton trucks with E load range tires run high pressure, and they have brass high pressure snap in valve stems. Without a high pressure valve stem, the stem can actually blow out of the tire. This usually happens on the interstate due to high temps and pressure increases due to the temp increase. At highway speeds, rapid pressure loss almost always causes the tire to have a cap separation as the side wall disintegrates. This rubber flapping around will usually tear the hell out of the truck, including ripping fenders and door sheet metal right off(Best Case). Or it can cause a serious accident (Worst Case).
Anyone remember the big Firestone Recall and Ford Explorer Recall? The roll over accidents were due to ford using too low a tire pressure than Firestone recommended for that tire. When the vehicles were loaded down and on the interstate the tire sidewall would fail. At the time Ford had a door jam pressure of around 24 psi.
The reason you get better gas mileage on higher pressure is due to less rolling resistance since only the center of the tire is in contact with the road. I would never run more than 35 psi or less than 27 on the street.
Many tricks for checking the contact patch. NEVER NEVER run the max PSI that is printed on the sidewall. This is the max cold pressure for maintaining maximum load capacity of the tire, and that rating will be much more than any of the Yota's here are rated for.
ALSO, anyone running more than 45 pounds on a standard valve stem is asking for trouble. Standard valve stems are only rated for 45-50 PSI, larger 3/4 and 1 ton trucks with E load range tires run high pressure, and they have brass high pressure snap in valve stems. Without a high pressure valve stem, the stem can actually blow out of the tire. This usually happens on the interstate due to high temps and pressure increases due to the temp increase. At highway speeds, rapid pressure loss almost always causes the tire to have a cap separation as the side wall disintegrates. This rubber flapping around will usually tear the hell out of the truck, including ripping fenders and door sheet metal right off(Best Case). Or it can cause a serious accident (Worst Case).
Anyone remember the big Firestone Recall and Ford Explorer Recall? The roll over accidents were due to ford using too low a tire pressure than Firestone recommended for that tire. When the vehicles were loaded down and on the interstate the tire sidewall would fail. At the time Ford had a door jam pressure of around 24 psi.
The reason you get better gas mileage on higher pressure is due to less rolling resistance since only the center of the tire is in contact with the road. I would never run more than 35 psi or less than 27 on the street.
Last edited by stanprophet; 11-06-2013 at 05:44 PM.
#159
Registered User
Tire Pressure
Just bought BFG A/T K02 265/75-16 and was installed @35#. Stock size was 265/70-16. I was not aware that the tires installed were E rated.
These were way to rough in city driving, The door said 29# front and 26# rear for stock size. The tire shop recommended 32#F and 29# rear.
This was a little better but still stiff ride, I believe it may be due to the E rating. I'll pay more attention to the load rating in the future.
2002 Tacoma ext cab 5 spd 3.4 V6 4x4 SR5 and TRD offroad susension
These were way to rough in city driving, The door said 29# front and 26# rear for stock size. The tire shop recommended 32#F and 29# rear.
This was a little better but still stiff ride, I believe it may be due to the E rating. I'll pay more attention to the load rating in the future.
2002 Tacoma ext cab 5 spd 3.4 V6 4x4 SR5 and TRD offroad susension
Thread
Thread Starter
Forum
Replies
Last Post
GreatLakesGuy
The Classifieds GraveYard
8
09-04-2015 09:27 AM
88yodabasket
86-95 Trucks & 4Runners
15
07-13-2015 01:32 PM