Just Found My Truck is Wired For an Alarm - Have ?s About Set UP
#1
Registered User
Thread Starter
Just Found My Truck is Wired For an Alarm - Have ?s About Set UP
Like it says, i was under the drivers saiod kick-panel lookingh for something and happened to notice a box with a bunch of circuit looking things zip-tied to the underside of the steering column area. Anyways, i followed the wires to two sets of prongs that were covered in a business card and wrapped in electrical tape.
I remembered these two box looking things that came with my 4Runner lying in the cargo area when i first boughtit. I had thrown them in the Pass. Side compartment and thought nothing of them.
So today as I was taking the tape off and realized the prongs looked very similar to the "box" looking things. So i rushed to the back grabbed one of them and proceded to plu it in. Immediately it starts going off....SUPER LOUD!! I unplug it and then plug in the otrher box, i hear "Viper Armed". THen hook up the other box and it starts going off again and say "Viper Armed Move Back" (or something like that).
I am soo excited at this point i want to just tinker with it. Here are some pics of the two boxes i have.
So basically im wondering how to make it no go off like crazy as soon as i plug it in. I do not have any kinmdf of remote for it yet. Please yall, i could really use some help with this.
On the Viper box the back of it points to the place where the 3 pin harness go in and says -
GREEN: (-) LOCK PULSE TO RELAY
RED: (+) 12 VOLT CONSTANT POWER
BLUE: (-) UNLOCK PULSE TO RELAY
The larger box says VIPER Auto Security Systems Model 300.
The smaller box says Auto Security Systems 516V
What are these three prongs supposed to be? I cannot fing any plug-ins in my teruck for these?
I remembered these two box looking things that came with my 4Runner lying in the cargo area when i first boughtit. I had thrown them in the Pass. Side compartment and thought nothing of them.
So today as I was taking the tape off and realized the prongs looked very similar to the "box" looking things. So i rushed to the back grabbed one of them and proceded to plu it in. Immediately it starts going off....SUPER LOUD!! I unplug it and then plug in the otrher box, i hear "Viper Armed". THen hook up the other box and it starts going off again and say "Viper Armed Move Back" (or something like that).
I am soo excited at this point i want to just tinker with it. Here are some pics of the two boxes i have.
So basically im wondering how to make it no go off like crazy as soon as i plug it in. I do not have any kinmdf of remote for it yet. Please yall, i could really use some help with this.
On the Viper box the back of it points to the place where the 3 pin harness go in and says -
GREEN: (-) LOCK PULSE TO RELAY
RED: (+) 12 VOLT CONSTANT POWER
BLUE: (-) UNLOCK PULSE TO RELAY
The larger box says VIPER Auto Security Systems Model 300.
The smaller box says Auto Security Systems 516V
What are these three prongs supposed to be? I cannot fing any plug-ins in my teruck for these?
Last edited by 881stGenRunner; 10-01-2007 at 05:43 PM.
#3
Registered User
Dont even bother, eventually you will find that the system has malfunctioned and locks you outta the car or disables the fuel pump-thats probably why it was taken off.
Thread
Thread Starter
Forum
Replies
Last Post
alfonz33
95.5-2004 Tacomas & 96-2002 4Runners
9
11-16-2015 09:21 AM
WTB[FourCorners]: 84-88 Toyota Pickup Doors with Auto Windows
subaruwrx88011
Vehicles - Parting Out
4
10-09-2015 12:39 PM
saphirekosmos
Newbie Tech Section
1
06-22-2015 10:26 AM