Hey there. I'm looking for the taillight connectors w pigtail wires to re wore my tail lights on 1987 pick up.
can you email me asap please

Brent

speedracer4044@gmail.com

Looking for two tail light wire harnesses for a Corolla Cross -- wanted to see if you're interested in putting together? I'm changing out tail lights from the US version to one that has amber turns. Many thanks!

Hello can you help with 82 pickup air, i have evap under dash bought a little harness and i do not think it is right a little and want to.make sure the connectors are right.
also looking for sub harness under hood. Do you have stuff like that.

Hello,
I came across some of your posts during a search for a 97 T100 ECU. I saw that you had bought a truck with a bad ecu and I was wondering if you still had that ecu and if you would sell it. I am making a patch harness for my 97 T100 to connect a stand-alone ecu so I dont have to hack the stock harness. I cant find a female connector for this project so I am looking for an ecu to rob the connector from.
Thanks,
Brian
b.stigler@comcast.net

part II (due to 1000char limit):

another option would be, that I try to make the wiring myself, but I would need advise where to buy the connectors. If you could give me any advise, i would appreciate a lot.

Hi atcfixer

I saw your posts reg A/C wiring and the harness you can produce.

My truck is a 92 Hilux SC (RN106 w/ 22re) and I bought new original toyota aircon kit from a 94 Hilux with Diesel engine (2L/3L). Unfortunately, my RN106 didnt have the wiring for a/c. I compared all the wiring diagrams. I concluded the "Diesel aircon" could work on the 22RE, s it requires less signals than the 22RE a/c (only 4 wires connected to the evaporator harness)
I would need a tailor-made harness, connecting from 10A a/c fuse (holder existing, but not wired) to A/C switch (Switch existing) to evaporator harness (i have this) plus a connection to the small 3-wire harness which connects to compressor and vsv (the 3 wire harness exists as well).
I would like to ask if I may send you a sketch based on the diagram, highlighting the existing connectors/harness and the harness I would need (guess the description above is too simple). I would pay a good price for a tailor made harness.


BR

Claudio

Hi atcfixer

I saw your Aug 2021 post regarding a starter relay rewire harness. I am interested in such a harness, if you are still building them. My truck is a 91 pickup manual transmission w/ the 5vze swap. I have been experiencing the intermittent starting issue described on the yotatech forum, where when the key is turned, there is just a click without the starter turning over. I've replaced my starter relay, clutch switch, ignition switch and starter (not in that order). One thing I'll add is that the starting problem happens more often when the ambient temperature is warm. Which points me to a problem in the cab, where the relay and switches are located for the 91. I get that it doesn't quite make sense, but it is an observable.

I am in the process of doing a swap T00 3.4 1996 to a 4.7 2Uz engine. Please advise on the wiring harness mod if you can.

I will try to respond again.Each time I try to respond it doesn't show that is has send. This is at least my third attempt. I need all the windshield trim, dome light, not the one located in the rear view mirror,clock, fuel gauge sending unit, switches located in the console, plastic gray pillar trim and the rod that is used to lower the spare tire. This rod will probably be too expensive to send but we will see. What would this cost including shipping to 39562? Thanks Ran

I have a couple, one from a 89 and the other from a 90, both 4x4 and 3.0L v6. Where are you located? I'm up in Michigan (mid part of the lower section of the state).