Triple guage dash pod
#1
Contributing Member
Thread Starter
Join Date: Aug 2002
Location: Home: Aurora, CO; Work: The People's Republic of Denver
Posts: 1,991
Likes: 0
Received 0 Likes
on
0 Posts
Triple guage dash pod
Has anyone seen one of these made for the 3rd gen 4Runner? I found one at Autometer for the Dodge Ram that might work:
http://hp.autometer.com/products/pro...0xx/015002.jpg
Waht do you all think? I see the only problem being the curved 4Runner dash vs. the flat Dodge dash, but a heat gun could be used to mould the pod to conform. I want to put the volt, oil press., and tranny temp up there to clean up my A-pillar.
http://hp.autometer.com/products/pro...0xx/015002.jpg
Waht do you all think? I see the only problem being the curved 4Runner dash vs. the flat Dodge dash, but a heat gun could be used to mould the pod to conform. I want to put the volt, oil press., and tranny temp up there to clean up my A-pillar.
#2
Registered User
Join Date: Jun 2003
Location: Daly City, CA
Posts: 900
Likes: 0
Received 0 Likes
on
0 Posts
this thread is a bit old but i want to clean up my a-pillar also, therefore i would need a new/used stock a-pillar and a new place to put guages so
BUMP BUMP BUMP BUMP BUMP BUMP BUMP BUMP BUMP BUMP BUMP BUMP
ttt ttt ttt ttt ttt ttt ttt ttt ttt ttt ttt ttt ttt ttt ttt ttt ttt ttt ttt ttt
BUMP BUMP BUMP BUMP BUMP BUMP BUMP BUMP BUMP BUMP BUMP BUMP
ttt ttt ttt ttt ttt ttt ttt ttt ttt ttt ttt ttt ttt ttt ttt ttt ttt ttt ttt ttt
#3
Registered User
3.4,
Whats wrong w/ your a-pillar mount? i just bought one from gaugepods.com. while *slightly* impairing vision to the left side, nothing that will prevent safe operation.
bob
Whats wrong w/ your a-pillar mount? i just bought one from gaugepods.com. while *slightly* impairing vision to the left side, nothing that will prevent safe operation.
bob
#4
Registered User
Join Date: Jun 2003
Location: Daly City, CA
Posts: 900
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by Bob_98SR5
3.4,
Whats wrong w/ your a-pillar mount? i just bought one from gaugepods.com. while *slightly* impairing vision to the left side, nothing that will prevent safe operation.
bob
Whats wrong w/ your a-pillar mount? i just bought one from gaugepods.com. while *slightly* impairing vision to the left side, nothing that will prevent safe operation.
bob
#5
Registered User
Originally Posted by 3.4v6
i had a triple gauge pod from a for zx-2 that i got from a buddy. i molded that onto my stock pillar so i had to make a bunch of holes (screws, wires). i took the pod and guages out today so now im left with a stock pillar with 3 1-inch holes and a bunch of little holes from screws. any idea where to get a new one besides the dealer?
bob
Thread
Thread Starter
Forum
Replies
Last Post
kawazx636
The Classifieds GraveYard
34
10-06-2021 03:03 PM
TheBFA
Solid Axle Swaps, All Years
8
02-15-2020 06:55 AM
zytra
86-95 Trucks & 4Runners
32
01-24-2019 03:16 PM
zombie_barbarossa
95.5-2004 Tacomas & 96-2002 4Runners
3
10-02-2015 10:54 PM
FS[PacNorWest]: 1987 4Runner SAS, 22RE, 5Spd, Dual Cases, etc
toyotasaurus
Vehicles - Trailers (Complete)
0
09-24-2015 03:30 PM