Seat Conversion 1994 extra cab 4X4
#1
Registered User
Thread Starter
Join Date: Oct 2004
Location: Indiana
Posts: 2
Likes: 0
Received 0 Likes
on
0 Posts
Seat Conversion 1994 extra cab 4X4
I am looking to convert my 1994 Toyota 4X4 Extra Cab Truck from a 60/40 seat too 2 Bucket seats.
I Have read all the posts on this forum in regards to Seats Mods, it does not sound to good far as a easy swap out/swap in. I will be contacting wedge engineering, and see what they can do.
I am looking to find a Drivers side Bucket Seat that will bolt up with factory seat mounts. Width=15 1/2 " Length=16"
The passenger side bucket seat mounts are not the same dimensions as the drivers side, but the factory passenger seat would be perfect if I could only mount on the drivers side.
I don't need anything fancy, factory would be fine used or new.
Any help anyone could provide would be great.
I have been to the Junks yards with no luck.
My truck is a daily drive truck and I am needing the above mod to gain space between the seats to mount radios and switch packs.
I have photos of the seat in question if needed please let me know.
I Have read all the posts on this forum in regards to Seats Mods, it does not sound to good far as a easy swap out/swap in. I will be contacting wedge engineering, and see what they can do.
I am looking to find a Drivers side Bucket Seat that will bolt up with factory seat mounts. Width=15 1/2 " Length=16"
The passenger side bucket seat mounts are not the same dimensions as the drivers side, but the factory passenger seat would be perfect if I could only mount on the drivers side.
I don't need anything fancy, factory would be fine used or new.
Any help anyone could provide would be great.
I have been to the Junks yards with no luck.
My truck is a daily drive truck and I am needing the above mod to gain space between the seats to mount radios and switch packs.
I have photos of the seat in question if needed please let me know.
#2
Registered User
Join Date: Jan 2004
Location: SW Ohio
Posts: 300
Likes: 0
Received 0 Likes
on
0 Posts
Going from a 60/40 to Toyota truck buckets ***of the same generation*** is one of the easier options (which is not to say it's without hassle).
I'm not 100% sure about a '94 pre-Taco, but on 95.5+ Tacos it's pretty much a straightforward bolt-in, 'cause the 60/40's and buckets use the same mounting configuration. I've been told it's the same for your generation pre-Taco, but I can't personally vouch for it... The worst hassles I've seen documented are:
- only 3 of 4 holes lining up 'as is' - requiring one more be drilled per seat
- modding to deal with a height difference between the 60/40's and buckets (though I've never been clear if it's the mounts or the seats themselves that are of differing heights).
I'm not 100% sure about a '94 pre-Taco, but on 95.5+ Tacos it's pretty much a straightforward bolt-in, 'cause the 60/40's and buckets use the same mounting configuration. I've been told it's the same for your generation pre-Taco, but I can't personally vouch for it... The worst hassles I've seen documented are:
- only 3 of 4 holes lining up 'as is' - requiring one more be drilled per seat
- modding to deal with a height difference between the 60/40's and buckets (though I've never been clear if it's the mounts or the seats themselves that are of differing heights).
Thread
Thread Starter
Forum
Replies
Last Post
Road Bull
86-95 Trucks & 4Runners
23
10-10-2015 04:55 PM
Steezy96yota
86-95 Trucks & 4Runners (Build-Up Section)
1
07-06-2015 10:00 AM