1ST Gen replacement consoles?
#1
Registered User
Thread Starter
Join Date: May 2004
Location: Lake Hopatcong, NJ
Posts: 126
Likes: 0
Received 0 Likes
on
0 Posts
1ST Gen replacement consoles?
I am looking to replace my beat up center console with something that has cup holders and a bit more storage...oh yea and high enough to rest my arm on it. Anyone have some ideas or links? The problem is the space is very narrow, I had a Bestop console laying around but it is too wide. I am meeting up with some friends with Xterra's over the weekend and will take some measurments to see if their comsoles will fit, I remember it being kind of narrow.
#2
Registered User
Join Date: May 2004
Location: Ft.Wayne,IN
Posts: 22
Likes: 0
Received 0 Likes
on
0 Posts
I just saw a pic of a guys 2001 that looked really nice, high enough, cup holders in front, narrow too.
Gonna check one out to see if it'll fit in my 95 Taco. Assume it will.
Gonna check one out to see if it'll fit in my 95 Taco. Assume it will.
#5
Registered User
Join Date: May 2002
Location: Seattle
Posts: 3,000
Likes: 0
Received 0 Likes
on
0 Posts
Lots of people have, it's just difficult to find information on what they did. A few have adapted units made by Tuffy, some have used consoles from newer vehicles, and others have scratch-built their own. I'm currently searching for a good '90-95 console to put in my '86, they have good spacing for my crawler box shifter but they're pretty rare.
Don't forget ebay.
Don't forget ebay.
#6
Registered User
Join Date: Sep 2002
Location: Littleton, CO
Posts: 498
Likes: 0
Received 0 Likes
on
0 Posts
I too would like to replace mine.... I've even called TOR (who's on this board) and they no longer make them ( i did score a new dash though ). I've replaced the foam on top, found some really dense foam, wrapped it in some vinyl and its good to go The foam is about 4 inches tall, so my arm lays across it perfectly.
I haven't really searched for any other options though...
I haven't really searched for any other options though...
Trending Topics
#8
Registered User
Join Date: May 2004
Location: Ft.Wayne,IN
Posts: 22
Likes: 0
Received 0 Likes
on
0 Posts
For the low end, I found a pretty nice unit at Autozone last week. Most of the ones they carry are junk, but they usually have one model that is decent. It just happened to fit between the seats and match my grey interior perfectly. Nice cupholder, plenty of storage and just high enough to work as an armrest. Just plain plastic though, no padding on top.
It looks like it belongs and I'm happy with it until I find a padded armrest OEM type to get.
It looks like it belongs and I'm happy with it until I find a padded armrest OEM type to get.
#9
Registered User
Thread Starter
Join Date: May 2004
Location: Lake Hopatcong, NJ
Posts: 126
Likes: 0
Received 0 Likes
on
0 Posts
Finally getting the Xterra console tomorrow, will post install pics over the weekend. Anyone with the heater specs/pics so I can tell if it might fit?
Thread
Thread Starter
Forum
Replies
Last Post
RedRunner_87
95.5-2004 Tacomas & 96-2002 4Runners (Build-Up Section)
84
06-01-2021 01:51 PM
tpd143
General Vehicle Related Topics (Non Year Related)
1
07-07-2015 09:06 AM
FS[SouthEast]: 1st Gen 4Runner Slider Window, Driver Side
coryc85
Misc Stuff (Vehicle Related)
0
07-06-2015 04:07 AM