FS[MidWest]: Parting Out 91 Standard Cab Pickup 22re
#1
Registered User
Thread Starter
Join Date: May 2016
Location: North-Central Kansas
Posts: 21
Likes: 0
Received 0 Likes
on
0 Posts
Parting Out 91 Standard Cab Pickup 22re
NO ENGINE PARTS
I'm parting out a clean 1991 22re. I bought it from a guy who took the engine out of it before he sold it to me. Though it's obviously wrecked, I saw the engine run and drove the truck before buying. He took the engine out later and sold it to me. I bought it in order to get rid of the stupid looking gangster rims on my own truck, as well as grab a few body parts.
Located in Marion, Kansas.
I'm thinking most suspension parts can be shipped for around $50 based on location, everything else we can just do what I usually do with used parts, which is sell it for about 50% of the RockAuto price, depending on how hard it is to get to. I hope this pricing is specific enough, as I don't want my post deleted. Mods, please inform me if more specific information is needed.
VIN is JT4RN81A9M5113806
I'm parting out a clean 1991 22re. I bought it from a guy who took the engine out of it before he sold it to me. Though it's obviously wrecked, I saw the engine run and drove the truck before buying. He took the engine out later and sold it to me. I bought it in order to get rid of the stupid looking gangster rims on my own truck, as well as grab a few body parts.
Located in Marion, Kansas.
I'm thinking most suspension parts can be shipped for around $50 based on location, everything else we can just do what I usually do with used parts, which is sell it for about 50% of the RockAuto price, depending on how hard it is to get to. I hope this pricing is specific enough, as I don't want my post deleted. Mods, please inform me if more specific information is needed.
VIN is JT4RN81A9M5113806
Last edited by Justin Lenhardt; 08-12-2016 at 07:29 AM.
#2
Registered User
iTrader: (2)
Join Date: Oct 2009
Location: Centeral Willamette Valley Oregon
Posts: 1,044
Likes: 0
Received 5 Likes
on
5 Posts
How much for the A/C hoses and all the factory tie downs from the bed? Shipping zip code is 97361.
Can you do me a favor and measure the motor mounts to the front of the frame horn? I also would really appreciate it if you could lay a tape measure across the frame so I can see the top of the upper control arm and the motor mount. I have been looking for this measurement and have had a hard time finding someone who would do this for me.
Thanks,
85Toyman
Can you do me a favor and measure the motor mounts to the front of the frame horn? I also would really appreciate it if you could lay a tape measure across the frame so I can see the top of the upper control arm and the motor mount. I have been looking for this measurement and have had a hard time finding someone who would do this for me.
Thanks,
85Toyman
#4
Registered User
Thread Starter
Join Date: May 2016
Location: North-Central Kansas
Posts: 21
Likes: 0
Received 0 Likes
on
0 Posts
Toyman, I'll get those measurements for you. And I'll get the hoses off and weighed and see how much it costs to ship as well.
nbl, I'd be fine cutting into the frame as well. PM me more specifics about which cuts you want. Also, are you wanting them shipped?
nbl, I'd be fine cutting into the frame as well. PM me more specifics about which cuts you want. Also, are you wanting them shipped?
#7
Trending Topics
#8
Registered User
Thread Starter
Join Date: May 2016
Location: North-Central Kansas
Posts: 21
Likes: 0
Received 0 Likes
on
0 Posts
Ok nbl, so I'm still not quite sure, I think you are saying you just want the bed side, right? Or would you like me to cut the entire bed horizontally from that point? In either case, I'd say $120 plus shipping? It doesn't matter to me how much you take, since the rest will just go to scrap. Let me know how that sounds
#9
How is the wiring ? I am looking for the Integration relay with the harness connectors and as much harness wire as practical. It's behind the passenger kick panel, and some of the harness goes thru the firewall/side.
Thanks,
Steve
Thanks,
Steve
#10
How about the battery tray support sheetmetal? The little platform on the passenger wheel well that is spot welded on? Mine is completely rotted away, but my fender survived it. You could just crudely cut away the fender around it and I'd drill the spot welds if it's in decent shape.
Oh, and what about the speedometer cable?
These parts would be shipped to Louisiana, 70360.
Oh, and what about the speedometer cable?
These parts would be shipped to Louisiana, 70360.
Last edited by supersaiyan93; 09-14-2016 at 07:13 AM.
#11
Registered User
Thread Starter
Join Date: May 2016
Location: North-Central Kansas
Posts: 21
Likes: 0
Received 0 Likes
on
0 Posts
Stephen, Super, I believe all the parts you are asking for are available, and I can start pulling them when we discuss price. I'll PM you both!
#17
Registered User
Thread Starter
Join Date: May 2016
Location: North-Central Kansas
Posts: 21
Likes: 0
Received 0 Likes
on
0 Posts
Sunvisors, Tailgate
Sorry for the long reply time Aberle, I've been dealing with a few potential buyers for the bed who keep backing out. Tailgate is straight and rust free. I've stolen the access panel off of it for my own truck though, will that be a problem?
And I'll get you some pictures of the sunvisors I8URSVT. They are in good condition.
And I'll get you some pictures of the sunvisors I8URSVT. They are in good condition.
#20
Sorry for the long reply time Aberle, I've been dealing with a few potential buyers for the bed who keep backing out. Tailgate is straight and rust free. I've stolen the access panel off of it for my own truck though, will that be a problem?
And I'll get you some pictures of the sunvisors I8URSVT. They are in good condition.
And I'll get you some pictures of the sunvisors I8URSVT. They are in good condition.
thanks for the reply but I found a brand new one off craigslist.